background image

Page 6

Bottom Return Air Applications

If return air is to terminate through the floor under the furĆ
nace,  a  direct,  airtight and sealed connection must be

made to the bottom of the furnace.
 1 - Cut  opening  in  floor  or  platform.  Using  knockouts

provided, cut bottom of base panel. See figure 2.

FIGURE 2

KNOCKOUT PATTERN FOR BOTTOM

RETURN AIR APPLICATION

FIGURE 3

G32V UNIT

RETURN AIR

PLENUM

PROPERLY

SIZED FLOOR

OPENING

BOTTOM RETURN AIR APPLICATION

 2 - Bend a flange on return air plenum and lower into

floor or platform opening. See figure 3.

 3 - Position unit over return air opening. Seal unit air

tight with return air plenum.

NOTE - Be careful not to damage insulation. Check for

tight seal.

Side Return Air Applications

For installations where the return air is taken from a return

air drop, unit may be installed using either the left or right

side of furnace.
For side return air applications, cut the furnace cabinet at

the dimensions given in the unit dimensions graphic. EmĆ

bossed corners are pro-vided on both cabinet sides for reĆ

turn air opening location.

Filter & Filter Assembly

A filter and an external filter rack for use in side return air

applications are shipped with the unit.

 

A filter must be in

place anytime the unit is in operation.

TABLE 2

FILTER SIZE REQUIREMENTS

UNIT MODEL

NUMBER

FILTER PART

NUMBER

FILTER SIZE

G32V-75

31J81

14 inches x 25 inches

(356 x 635 mm)

G32V-100

G32V-125

P-8-7831

20 inches x 25 inches

(508 x 635 mm)

Bottom Return Air Applications

 1 - Remove blower access panel.
 2 - Install  filter  clips,  provided  with  unit,  by  slipping

folded section of clip on edge of bottom opening. See

figure 4.

FIGURE 4

BOTTOM RETURN FILTER INSTALLATION

FURNACE

BASE BOTTOM

REAR FILTER CLIP

RETURN AIR OPENING

SIDE FILTER CLIPS (2)

FURNACE

FRONT

FURNACE

BACK

 3 - Place filter in bottom of blower compartment beneath

rear filter clip. Press down on filter sides. Filter clips

flex allowing filter to snap into place.

 4 - To remove filter, press clip and pull filter up and out.

Side Return Air Applications

 1 - Align filter rack opening with the inside edge of the

side  return  opening.  Bottom  of  rack  should  be
approximately 1 inch (25 mm) from the bottom and 3

inches (76 mm) from the front of the unit.

 2 - Screw filter rack into place with the eight self drill, self

tap screws provided. See figure 5.

 3 - Push filter door pins through the two holes in filter

door from the inside of the uĆchannel. See figure 6.

FIGURE 5

SIDE RETURN FILTER INSTALLATION

RETURN

AIR

OPENING

12 in. (305) for

14 in. (356) Filter

18 in. (457) for

20 in. (508) Filter

1-15/16 in.

(49)

BLOWER DECK

15/16 in

(24)

CABINET BASE BOTTOM

RETURN AIR

PLENUM SIZE

12-3/4 in X 23-1/2 in (324 X

597) for 14 in (356) Filter

18-3/4 in. x 23-1/2 in.

(476 x 597)

for 20 in. (508) Filter

in. (mm)

Summary of Contents for G32V3-75











































Reviews: