background image

Chapter 6. Symptom-to-FRU Index

      21

POST Error Message

Description/Action

CMOS Date/Time Not Set

The CMOS Date and/or Time are 
invalid. This error can be resolved 
by readjusting the system time in 
Phenix BIOS Setup.

CMOS Battery Low

The CMOS battery is no longer 
functional.
Replace the battery.

CMOS Checksum Bad 

Checksum of CMOS is incorrect.
The computer loads the default 
configuration settings. This error 
might indicate that CMOS has 
become corrupt due to a weak 
CMOS battery.

Primary Master Hard Disk Error

The IDE/ATAPI device configured 
as Primary Master/Primary Slave/
Secondary Master/Secondary Slave 
could not be found or initialized. 
Make sure the hard drive is correctly 
installed.

Primary Slave Hard Disk Error

Secondary Master Hard Disk Error

Secondary Slave Hard Disk Error

Keyboard not found

Cannot initialize the keyboard.
Make sure the keyboard is properly
connected to the computer and
that no keys are held pressed during
POST.
To purposely configure the
computer without a keyboard, set
keyboardless operation in Setup to
Enable. The BIOS then ignores the
missing keyboard during POST.

System Halted

The system has been halted. A reset 
or power cycle is required to reboot 
the machine. This message appears 
after a fatal error has been detected.

Reboot and Select proper Boot
device or Insert Boot Media in
selected Boot device and press a key

The BIOS was unable to find a
suitable boot device.
Make sure the boot drive is properly
connected to the computer.
Make sure you have bootable
media.

Summary of Contents for 40813AU













































Reviews: