Lenovo 6241 Installation And Service Manual Download

Page: 70 / 1990

• Memory rank sparing is not supported if memory mirroring is enabled.

• The spare rank must have identical or larger memory capacity than all the other ranks on the same DDR3

or DDR4 channel.

• When single-rank DIMMs (that is, 4 GB and 8 GB) are used, a minimum of two rank DIMMs must be

installed per memory channel to support memory sparing.

• When multi-rank DIMMs (that is, 16 GB, 32 GB, and 64 GB) are used, one multi-rank DIMM can be

installed per memory channel to support memory sparing.

• The total memory available in the system is reduced by the amount of memory allocated for the spare

ranks.

System x3850 X6 and x3950 X6 Installation and Service Guide

Summary of Contents for 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands

Lenovo 6241, Installation And Service Manual

Search results

Summary of Contents for 6241

Reviews:

Related manuals for 6241

Brands by name

Popular brands