•
Load Default Settings
Select this choice to cancel the changes that you have made in the settings and restore the factory
settings. This choice is on the full Setup utility menu only.
•
Exit Setup
Select this choice to exit from the Setup utility. If you have not saved the changes that you have made in
the settings, you are asked whether you want to save the changes or exit without saving them.
Passwords
This topic provides information on setting passwords in the server Setup utility.
From the
User Security
menu choice in the Setup utility, you can set, change, and delete a power-on
password and an administrator password. The
User Security
choice is on the full Setup utility menu only.
If you set only a power-on password, you must type the power-on password to complete the system startup
and to have access to the full Setup utility menu.
An administrator password is intended to be used by a system administrator; it limits access to the full Setup
utility menu. If you set only an administrator password, you do not have to type a password to complete the
system startup, but you must type the administrator password to access the Setup utility menu.
If you set a power-on password for a user and an administrator password for a system administrator, you
can type either password to complete the system startup. A system administrator who types the
administrator password has access to the full Setup utility menu; the system administrator can give the user
authority to set, change, and delete the power-on password. A user who types the power-on password has
access to only the limited Setup utility menu; the user can set, change, and delete the power-on password, if
the system administrator has given the user that authority.
Power-on password
This topic provides information about setting a power-on password using the server Setup utility.
If a power-on password is set, when you turn on the server, the system startup will not be completed until
you type the power-on password. You can use any combination of 6 to 20 printable ASCII characters for the
password.
When a power-on password is set, you can enable the Unattended Start mode, in which the keyboard and
mouse remain locked but the operating system can start. You can unlock the keyboard and mouse by typing
the power-on password.
If you forget the power-on password, you can regain access to the server in any of the following ways:
• If an administrator password is set, type the administrator password at the password prompt. Start the
Setup utility and reset the power-on password.
• Remove the battery from the server, wait 30 seconds, and then reinstall it.
• Change the position of the power-on password switch to 1 on the SW1 switch block to bypass the power-
on password check.
128
System x3850 X6 and x3950 X6 Installation and Service Guide
Summary of Contents for 6241
