Lenovo 7X20 Manual Download | Manualshive

Page: 187 / 226

background image

Severity: Warning

User Action:

Complete the following steps:

1. It's a security warning message when user want to boot from an unauthorized UEFI image or OS

while Secure Boot is enabled and Secure Boot Mode is in User Mode. If customer does not want to
boot any unauthorized UEFI image or OS, please remove that bootable device.

2. If customer does want to boot this unauthorized UEFI image or OS, there're two ways to allow

system boot from this unauthorized image, the first is to disable Secure Boot, the second is to enroll
the unauthorized image into DB(Authorized Signature Database).

a. Disable Secure Boot: assert Physical Presence and then change Secure Boot Setting to Disable (

in F1 Setup -> System Settings -> Security -> Security Boot Configuration -> Security Boot
Setting).

b. Enroll the unauthorized UEFI Image. assert the Physical Presence and then change Secure Boot

Policy to Custom Policy ( in Setup -> System Settings -> Security -> Security Boot Configuration
-> Security Boot Policy), then enter into "Security Boot Custom Policy" Menu, press the "Enroll Efi
Image" button, select the unauthorized UEFI Image in the popup box. (NOTE: There're two ways
to assert Physical Presence. 1) switch Physical Presence Jumper to ON ; 2) If the Physical
Presence Policy has been set to enabled ( F1 Setup -> System Settings -> Security -> Physical
Presence Policy Configuration), user is allowed to assert remote Physical Presence via IPMI tool.)

3. If the problem persists, collect Service Data logs.

4. Contact Lenovo Support.

•

FQXSFPU0023I: Secure Boot Image Verification Failure has been cleared as no failure in this round

boot.

Severity: Info

User Action:

Information only; no action is required.

•

FQXSFPU0027N: System uncorrectable error has occurred on Processor [arg1] Core [arg2] MC

bank [arg3] with MC Status [arg4], MC Address [arg5], and MC Misc [arg6].

Severity: Fatal

User Action:

Complete the following steps:

1. Perform a virtual reseat or AC cycle the server.

2. If the problem returns Collect Service Data log.

3. Contact Lenovo Support.

•

FQXSFPU0030N: A firmware fault has been detected in the UEFI image.

Severity: Error

User Action:

Complete the following steps:

1. Check Lenovo support site for an applicable service bulletin or firmware update that applies to this

error.

2. Reflash UEFI image.

3. Undo recent system changes (settings or devices added). Verify that the system boots. Then, re-

install options one at a time to locate the problem.

.

183

«
...
185
186
187
188
189
...
»

Summary of Contents for 7X20



































































































































































































































Reviews:

No comments

Related manuals for 7X20

Brand: Lindy Pages: 2

Brand: Conteg Pages: 40

CompactPCI MIC-3041

Brand: Advantech Pages: 2

Brand: Artesyn Pages: 3

Brand: Charles Pages: 13

Brand: Hartmann Pages: 8

Brand: AEONS Technologies Pages: 12

Classic Series Classic 410E

Brand: Peavey Pages: 2

DTH Concert Sub II

Brand: Peavey Pages: 4

SmartRack SRWF5U

Brand: Tripp Lite Pages: 8

SmartRack SRW12UHD

Brand: Tripp Lite Pages: 24

SmartRack SRW12U13

Brand: Tripp Lite Pages: 24

Brand: Pulsar Pages: 6

Brand: i-tec Pages: 24

THUNDER FORM F250X00BK20A-TN

Brand: MTX Pages: 12

FieldSmart Fiber Active Cabinet (FAC) 900

Brand: Clearfield Pages: 163

Brand: Xcellon Pages: 16

Brand: Macpower & Tytech Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands