Lenovo 7X20 Manual Download | Manualshive

Page: 19 / 226

background image

The zero output functions abnormally

Severity: Informational

User Action:

Information only; no action is required.

•

080801E0: PS1: Power Supply, Device Inserted / Device Present was asserted.

The PSU is installed in the indicated slot.

Severity: Informational

User Action:

Information only; no action is required.

•

080801E1: PS2: Power Supply, Device Inserted / Device Present was asserted.

The PSU is installed in the indicated slot.

Severity: Informational

User Action:

Information only; no action is required.

•

086F0180: PS1_12Va_OC_ERR: Power Supply, Power Supply Failure detected was asserted.

The 12V AUX output current experiences a current load greater than the current limit

Severity: Critical

User Action:

1. Check power supply LEDs

–  If AC LED is not lit, check power cord and input voltage.
–  If DC LED is not lit, remove and reinstall power supply.
–  If error LED is lit, replace the power supply.

2. If fault recurs, please call service.

•

086F0181: PS2_12Va_OC_ERR: Power Supply, Power Supply Failure detected was asserted.

The 12V AUX output current experiences a current load greater than the current limit

Severity: Critical

User Action:

1. Check power supply LEDs

–  If AC LED is not lit, check power cord and input voltage.
–  If DC LED is not lit, remove and reinstall power supply.
–  If error LED is lit, replace the power supply.

2. If fault recurs, please call service.

•

086F0182: PS1_12Va_OV_ERR: Power Supply, Power Supply Failure detected was asserted.

The 12V AUX output voltage reaches overvoltage lockout limit

Severity: Critical

User Action:

1. Check power supply LEDs

–  If AC LED is not lit, check power cord and input voltage.
–  If DC LED is not lit, remove and reinstall power supply.
–  If error LED is lit, replace the power supply.

2. If fault recurs, please call service.

.

15

«
...
17
18
19
20
21
...
»

Summary of Contents for 7X20



































































































































































































































Reviews:

No comments

Related manuals for 7X20

Brand: Hamlet Pages: 4

PLUSView1000 AMG User’s

Brand: Antec Pages: 3

Brand: Ewent Pages: 8

performa elite400

Brand: hager Pages: 4

Brand: König Electronic Pages: 16

Brand: Lava Pages: 2

Brand: Renkforce Pages: 4

Brand: Renkforce Pages: 8

Brand: Fantec Pages: 6

Brand: Fantec Pages: 20

Brand: XCLIO Pages: 4

Brand: SINGULARITY COMPUTERS Pages: 17

Brand: CommScope Pages: 2

FOSC-ACC-B-TRAY-12-RBN

Brand: CommScope Pages: 6

Brand: CommScope Pages: 2

RTX Secure 222-3QR

Brand: CRU Pages: 9

Brand: Campbell Pages: 32

Brand: Leviton Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands