Lenovo 7X20 Manual Download

Page: 9 / 226

User Action:

1. Reseat SMM module.

2. If 12V_SENSE error is still asserted, replace SMM module.

•

0201021B: 3V3_SENSE: Voltage sensor, critical event was asserted, reading value %V (Threshold

%V)

Asserted when voltage sensed on 3.3V power rail is lower than lower critical threshold or higher than
upper critical threshold

Severity: Critical

User Action:

1. Reseat SMM module.

2. If 3V3_SENSE error is still asserted, replace SMM module.

•

0201021C: 5V_SENSE: Voltage sensor, critical event was asserted, reading value %V (Threshold %

Asserted when voltage sensed on 5V power rail is lower than lower critical threshold or higher than upper
critical threshold

Severity: Critical

User Action:

1. Reseat SMM module.

2. If 5V_SENSE error is still asserted, replace SMM module.

•

0201021D: 2V5_SENSE: Voltage sensor, critical event was asserted, reading value %V (Threshold

%V)

Asserted when voltage sensed on 2.5V power rail is lower than lower critical threshold or higher than
upper critical threshold

Severity: Critical

User Action:

1. Reseat SMM module.

2. If 2V5_SENSE error is still asserted, replace SMM module.

•

0201021E: 1V2_SENSE: Voltage sensor, critical event was asserted, reading value %V (Threshold %

Asserted when voltage sensed on 1.2V power rail is lower than lower critical threshold or higher than
upper critical threshold

Severity: Critical

User Action:

1. Reseat SMM module.

2. If 1V2_SENSE error is still asserted, replace SMM module.

•

0201021F: 1V15_SENSE: Voltage sensor, critical event was asserted, reading value %V (Threshold

%V)

Asserted when voltage sensed on 1.15V power rail is lower than lower critical threshold or higher than
upper critical threshold

Severity: Critical

User Action:

Chapter 2

SMM2 events

Summary of Contents for 7X20



































































































































































































































Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands

Lenovo 7X20, Manual

Search results

Summary of Contents for 7X20

Reviews:

Related manuals for 7X20

Brands by name

Popular brands