background image

Figure 3. Using the Cisco Catalyst Switch Module 3012 to route the four Ethernet ports from the integrated

controller and a CFFv or CIOv expansion card

Table 5 lists the components that are used in the four-port configuration shown in Figure 3.

Table 5. Components used in the four-ports-per-server configuration

Diagram
reference

Part number /
machine type

Description

Quantity

Varies

BladeCenter HS22 or other supported server

1 to 14

None

Ethernet controller on the system board of the server

1 per
server

Varies

Compatible CFFv or CIOv expansion card (see Table 3)

1 per
server

Varies

Any BladeCenter chassis (see Table 2)*

1

43W4395

Cisco Catalyst Switch Module 3012 routing signals from the
CFFv or CIOv card 

2

43W4395

Cisco Catalyst Switch Module 3012 routing signals from the
integrated controller 

2

*Note: The expansion card can be installed in servers in the BladeCenter S (8886). However, by doing so,

you lose the ability to connect to the BladeCenter S Disk Storage Modules (DSMs). The Ethernet expansion

card goes in the place of the SAS expansion card that is needed to connect to the DSMs. This might be

appropriate for clients that want to use external iSCSI storage or need more than four Ethernet ports per

blade. If you are simply looking for redundant Ethernet switches or four Ethernet ports per blade, consider

using the 2/4 Port Ethernet Expansion Card (CFFh), part number 44W4479.

Maximum configuration: Eight Ethernet ports per server

Since BladeCenter servers support a CFFh expansion card plus either a CFFv or CIOv card (depending on

the model of the server), you can install up to eight Cisco Catalyst Switch Module 3012 devices in a

BladeCenter H chassis or BladeCenter HT. Figure 4 shows this eight-port solution. All connections between

the cards and the switch modules are internal to the chassis. No cabling is needed.

Cisco Catalyst Switch Module 3012 for BladeCenter (withdrawn product)

10

Summary of Contents for Cisco Catalyst 3012
















Reviews: