•
Message
: 2100: Detection error on HDD0 (Main HDD)
Solution
: The hard disk drive is not working. Have the hard disk drive serviced.
•
Message
: 2101: Detection error on SSD1 (M.2)
Solution
: The M.2 solid-state drive is not working. Have the M.2 solid-state drive serviced.
•
Message
: 2102: Detection error on SSD2 (M.2)
Solution
: The M.2 solid-state drive is not working. Have the M.2 solid-state drive serviced.
•
Message
: 2110: Read error on HDD0 (Main HDD)
Solution
: The hard disk drive is not working. Have the hard disk drive serviced.
•
Message
: 2111: Read error on SSD1 (M.2)
Solution
: The M.2 solid-state drive is not working. Have the M.2 solid-state drive serviced.
•
Message
: 2112: Read error on SSD2 (M.2)
Solution
: The M.2 solid-state drive is not working. Have the M.2 solid-state drive serviced.
•
Message
: 2200: Machine Type and Serial Number are invalid.
Solution
: Machine Type and Serial Number are invalid. Have the computer serviced.
•
Message
: 2201: Machine UUID is invalid.
Solution
: Machine UUID is invalid. Have the computer serviced.
•
Message
: Fan error
Solution
: Cooling fan has failed. Shut down the computer immediately and have the computer serviced.
•
Message
: Thermal sensing error
Solution
: The thermal sensor has a problem. Shut down the computer immediately and have the
computer serviced.
•
Message
: Bottom Cover Tamper Detection Error
Solution
: The Bottom Cover Tamper Switch is not working. Have the computer serviced.
•
Message
: Error: The non-volatile system UEFI variable storage is nearly full.
Note:
This error indicates that the operating system or programs cannot create, modify, or delete data in
the non-volatile system UEFI variable storage due to insufficient storage space after POST.
The non-volatile system UEFI variable storage is used by the UEFI BIOS and by the operating system or
programs. This error occurs when the operating system or programs store large amounts of data in the
variable storage. All data needed for POST, such as BIOS setup settings, chipset, or platform
configuration data, are stored in a separate UEFI variable storage.
Solution
: Press F1 after the error message is displayed to enter ThinkPad Setup. A dialog asks the user
for confirmation to clean up the storage. If the user selects “Yes”, all data that were created by the
operating system or programs will be deleted except global variables defined by the Unified Extensible
Firmware Interface Specification. If the user selects “No”, all data will be kept, but the operating system or
programs will not be able to create, modify, or delete data in the storage.
If this error happens at a service center, Lenovo authorized service personnel will clean up the non-volatile
system UEFI variable storage using the preceding solution.
Beep errors
Lenovo SmartBeep technology enables you to decode beep errors with your smartphone when a black
screen occurs with beeps from your computer. To decode the beep error with Lenovo SmartBeep
technology, do the following:
1. Go to
https://support.lenovo.com/smartbeep
or scan the following QR Code.
82
P52 User Guide
Summary of Contents for ThinkPad P52
