background image

7. Click

Filesystem

and open the /etc/modprobe.d/blacklist.conf file.

8. In the blacklist.conf window, type the following command:

blacklist nouveau

9. Save the configuration and close the window.

10. Open the /etc/grub.conf file.

11. In the grub.conf window, type the following command:

nouveau.modeset=0 rdblacklist=nouveau

12. Save the configuration and close the window.

13. Open the /etc/inttab file.

14. In the inttab window, change

id:5:initdefault:

into

id:3:initdefault:

.

15. Save the configuration and close the window.

16. Restart the server and select the

base

kernel.

17. Log in to the

base

kernel by entering your user name and password. Then press Enter.

18. Type the following command lines:

cd /tmp
./NVIDIA-NVS300-Quadro600-Linux-x86-310.19.run

19. When prompted, select

Accept

and press Enter.

Note:

If you are installing the driver on the operating system (64-bit), when the message

Install NVIDIA’s

32-bit compatibility OpenGL libraries ?

is displayed, configure the settings and press Enter.

20. When the message

Would you like to......

is displayed, select

Yes

and press Enter.

21. When the message

Your X configuration......

is displayed, select

OK

and press Enter.

22. Restart the server and log in to the

base

kernel.

23. Use the

startx

command to enter the graphics window and double-click

Computer

.

24. Click

Filesystem

and open the /etc/inttab file.

25. In the inttab window, change

id:3:initdefault:

into

id:5:initdefault:

.

26. Save the configuration and close the window.

27. Restart the server and the driver installation is completed.

Installing the driver for an HBA card

To install the driver for an HBA card, do the following:

1. Copy the HBA card driver from the

ThinkServer EasyStartup

DVD to your local drive. Double-click the

EXE file to unzip it to a folder. Copy the folder to a USB storage device and connect the USB storage
device to your server.

2. Log in to the operating system and copy the folder from the USB storage device to the

/tmp

directory

on your server.

Chapter 2

.

Installing an operating system in legacy mode

29

Summary of Contents for ThinkServer TD340



















































































Reviews: