Lenovo x3650 M5 Installation And Service Manual Download

Page: 1297 / 1340

•

215-804-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. The media tray is open.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Close the media tray and wait for 15 seconds for the media to be recognized. Run the test again.

2. Insert a new CD or DVD into the drive and wait for 15 seconds for the media to be recognized.

Rerun the test.

3. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

4. Run the test again.

5. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

215-901-000 : Optical Drive Test Aborted

Optical Drive Test Aborted. Drive media is not detected.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Insert a new CD or DVD into the drive and wait for 15 seconds for the media to be recognized.

Rerun the test.

2. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

3. Run the test again.

Appendix C. DSA diagnostic test results

1285

«
...
1295
1296
1297
1298
1299
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands