Lenovo x3650 M5 Installation And Service Manual Download

Page: 1299 / 1340

User Response

Complete the following steps:

1. Insert a new CD or DVD into the drive and wait for 15 seconds for the media to be recognized.

Rerun the test.

2. Check the drive cabling for loose or broken connections at both ends or damage to the cable.

Replace the cable if damage is present.

3. Run the test again.

4. Check system firmware level and upgrade if necessary.The installed firmware level can be found

in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

5. Run the test again.

6. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA system management test results

The following messages can result when you run the system management test.

Test results for the DSA system management test

The following messages can result when you run the DSA system management test.

•

166-000-001 : IMM I2C Test Passed

IMM I2C Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

166-801-001 : IMM I2C Test Aborted

Appendix C. DSA diagnostic test results

1287

«
...
1297
1298
1299
1300
1301
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands