Lenovo x3650 M5 Installation And Service Manual Download

Page: 428 / 1340

Alert Category

System - Remote Login

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0157

User Response

Information only; no action is required.

•

4000009e-00000000 : Login ID: [arg1] from [arg2] at IP address [arg3] has been logged off.

This message is for the use case where a user has been logged off of a Management Controller.

May also be shown as 4000009e00000000 or 0x4000009e00000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Remote Login

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0158

User Response

Information only; no action is required.

•

4000009f-00000000 : User [arg1] has initiated a TKLM Server Connection Test to check connectivity

to server [arg2].

User initiated a TKLM Server Connection test.

May also be shown as 4000009f00000000 or 0x4000009f00000000

Severity

Info

Serviceable

Automatically notify support

416

Lenovo System x3650 M5 Installation and Service Guide

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands