Lenovo x3650 M5 Installation And Service Manual Download

Page: 471 / 1340

Automatically notify support

Alert Category

Warning - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0490

User Response

1. Make sure that the fans are operating, that there are no obstructions to the airflow (front and

rear of the server), that the air baffle is in place and correctly installed, and that the server cover
is installed and completely closed.

2. Check the ambient temperature. You must be operating within the specifications (see Server

Features and specifications for more information).

3. Make sure that the heat sink for microprocessor n.

4. (Trained technician only) Replace system board.

•

80010701-2d01ffff : Numeric sensor [NumericSensorElementName] going high (upper non-critical)

has asserted. (PCH Temp)

This message is for the use case when an implementation has detected an Upper Non-critical sensor
going high has asserted.

May also be shown as 800107012d01ffff or 0x800107012d01ffff

Severity

Warning

Serviceable

Yes

Automatically notify support

Alert Category

Warning - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0490

User Response

1. Make sure that the fans are operating, that there are no obstructions to the airflow (front and

rear of the server), that the air baffle is in place and correctly installed, and that the server cover
is installed and completely closed.

2. Check the ambient temperature. You must be operating within the specifications (see Server

Features and specifications for more information).

Appendix A. Integrated management module II (IMM2) error messages

459

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands