Lenovo x3650 M5 Installation And Service Manual Download

Page: 614 / 1340

2. Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling

the drive) b. Cable from the system board to the backplane

3. Replace the following components one at a time, in the order shown, restarting the server

each time: a. Hard disk drive b. Cable from the system board to the backplane c. Hard disk
drive backplane (n = hard disk drive number)

•

806f010d-0420ffff : The Drive [StorageVolumeElementName] has been disabled due to a detected

fault. (Ext Drive)

This message is for the use case when an implementation has detected a Drive was Disabled due to fault.

May also be shown as 806f010d0420ffff or 0x806f010d0420ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Hard Disk drive

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0164

User Response

1. Run the hard disk drive diagnostic test on drive n.

2. Reseat the following components: a. Hard disk drive (wait 1 minute or more before reinstalling

the drive) b. Cable from the system board to the backplane

3. Replace the following components one at a time, in the order shown, restarting the server

each time: a. Hard disk drive b. Cable from the system board to the backplane c. Hard disk
drive backplane (n = hard disk drive number)

•

806f010f-2201ffff : The System [ComputerSystemElementName] encountered a firmware hang.

(Firmware Error)

This message is for the use case when an implementation has detected a System Firmware Hang.

May also be shown as 806f010f2201ffff or 0x806f010f2201ffff

Severity

Error

Serviceable

Yes

602

Lenovo System x3650 M5 Installation and Service Guide

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands