Lenovo x3650 M5 Installation And Service Manual Download

Page: 617 / 1340

•

806f011b-0c01ffff : The connector [PhysicalConnectorElementName] has encountered a

configuration error. (FP LCD Cable)

This message is for the use case when an implementation has detected an Interconnect Configuration
Error.

May also be shown as 806f011b0c01ffff or 0x806f011b0c01ffff

Severity

Error

Serviceable

Yes

Automatically notify support

Yes

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0266

User Response

1. Check system event log is showing LCD cable sensor has deasserted.

2. Reseat LCD cable on the system board.

3. Reset LCD cable on LCD panel.

Replace LCD cable.

•

806f0123-2101ffff : Reboot of system [ComputerSystemElementName] initiated by

[WatchdogElementName]. (IPMI Watchdog)

This message is for the use case when an implementation has detected a Reboot by a Watchdog occurred.

May also be shown as 806f01232101ffff or 0x806f01232101ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Appendix A. Integrated management module II (IMM2) error messages

605

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands