Lenovo x3650 M5 Installation And Service Manual Download | Manualshive

Page: 649 / 1340

background image

Error

Serviceable

Yes

Automatically notify support

No

Alert Category

Critical - Memory

SNMP Trap ID

41

CIM Information

Prefix:

PLAT

ID:

0136

User Response

Note: Each time you install or remove a DIMM, you must disconnect the server from the power
source; then, wait 10 seconds before restarting the server.

1. Refer to TIP H212293 for minimum code level.

2. Check the Lenovo support website for an applicable retain tip or firmware update that applies

to this memory error.

3. Make sure that the DIMMs are firmly seated and no foreign material is found in the DIMM

connector. Then, retry with the same DIMM.

4. If the problem is related to a DIMM, replace the failing DIMM indicated by the error LEDs.

5. If the problem occurs on the same DIMM connector, swap the affected DIMMs (as indicated

by the error LEDs on the system board or the event logs) to a different memory channel or
microprocessor.

6. (Trained technician only) If the problem occurs on the same DIMM connector, check the DIMM

connector. If the connector contains any foreign material or is damaged, replace the system
board.

7.

(Trained service technician only) Remove the affected microprocessor and check the

microprocessor socket pins for any damaged pins. If a damage is found, replace the system
board.

8. (Trained service technician only) If the problem is related to microprocessor socket pins,

replace the system board.

•

806f030c-2006ffff : Scrub Failure for [PhysicalMemoryElementName] on Subsystem

[MemoryElementName]. (DIMM 6)

This message is for the use case when an implementation has detected a Memory Scrub failure.

May also be shown as 806f030c2006ffff or 0x806f030c2006ffff

Severity

Error

Serviceable

Yes

Automatically notify support

No

Appendix A. Integrated management module II (IMM2) error messages

637

«
...
647
648
649
650
651
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

Brand: Aastra Pages: 592

Brand: IBM Pages: 54

Brand: Rack Solutions Pages: 8

847620U - Netfinity 3000 - 20U

Brand: IBM Pages: 270

Brand: IBM Pages: 220

Brand: Sun Oracle Pages: 222

Brand: LevelOne Pages: 88

AcquiLite EMB A7810

Brand: Obvius Pages: 29

FusionServer XH321 V5

Brand: xFusion Digital Technologies Pages: 76

HL-3400CN Series

Brand: Brother Pages: 280

Brand: Brother Pages: 308

2200W - NC Print Server

Brand: Brother Pages: 75

Brand: Brother Pages: 148

HL-3400CN Series

Brand: Brother Pages: 8

Brand: Samsung Pages: 58

APOGEE Ethernet Microserver 2100

Brand: Siemens Pages: 2

Brand: Siemens Pages: 38

Brand: Siemens Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands