Lenovo x3650 M5 Installation And Service Manual Download

Page: 900 / 1340

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0525

User Response

No action; information only.

•

81070608-0a01ffff : Sensor [SensorElementName] has deasserted the transition to

non-recoverable. (PS1 12V OC Fault)

This message is for the use case when an implementation has detected that the Sensor transition to
non-recoverable has deasserted.

May also be shown as 810706080a01ffff or 0x810706080a01ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Power

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0531

User Response

No action; information only. PS1 12V OV Fault : PS1 12V UV Fault : PS1 12Vaux Fault :

•

81070608-0a02ffff : Sensor [SensorElementName] has deasserted the transition to

non-recoverable. (PS2 12V OC Fault)

This message is for the use case when an implementation has detected that the Sensor transition to
non-recoverable has deasserted.

May also be shown as 810706080a02ffff or 0x810706080a02ffff

888

Lenovo System x3650 M5 Installation and Service Guide

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands