Lenovo x3650 M5 Installation And Service Manual Download | Manualshive

Page: 113 / 1340

background image

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• If an action step is preceded by “(Trained technician only),” that step must be performed only by a trained

technician.

• Go to the support website at http://www.lenovo.com/support to check for technical information, hints, tips,

and new device drivers or to submit a request for information.

Symptom

Action

The server does not turn off.

1. Determine whether you are using an Advanced Configuration and Power

Interface (ACPI) or a non-ACPI operating system. If you are using a non-ACPI
operating system, complete the following steps:

a. Press

Ctrl+Alt+Delete

.

b. Turn off the server by pressing the power-control button and hold it down for

5 seconds.

c. Restart the server.

d. If the server fails POST and the power-control button does not work,

disconnect the power cord for 20 seconds; then, reconnect the power cord
and restart the server.

2. If the problem remains or if you are using an ACPI-aware operating system,

suspect the system board.

The server unexpectedly shuts
down, and the LEDs on the
operator information panel are
not lit.

See “Solving undetermined problems” on page 106.

Serial-device problems

Use the troubleshooting tables to find solutions to problems that have identifiable symptoms.

• Follow the suggested actions in the order in which they are listed in the Action column until the problem is

solved.

• If an action step is preceded by “(Trained technician only),” that step must be performed only by a trained

technician.

• Go to the support website at http://www.lenovo.com/support to check for technical information, hints, tips,

and new device drivers or to submit a request for information.

Symptom

Action

The number of serial ports that
are identified by the operating
system is less than the number
of installed serial ports.

1. Make sure that:

• Each port is assigned a unique address in the Setup Utility and none of the

serial ports is disabled.

• The serial-port adapter (if one is present) is seated correctly.

2. Reseat the serial port adapter.

3. Replace the serial port adapter.

A serial device does not work.

1. Make sure that:

• The device is compatible with the server.
• The serial port is enabled and is assigned a unique address.
• The device is connected to the correct connector (see “System-board

internal connectors” on page 29).

2. Reseat the following components:

a. Failing serial device

b. Serial cable

3. Replace the components listed in 2 on page 102 one at a time, in the order

shown, restarting the server each time.

4. (Trained technician only) Replace the system board.

Troubleshooting

101

«
...
111
112
113
114
115
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

Brand: Xerox Pages: 2

Brand: Xerox Pages: 2

Brand: Xantech Pages: 52

NPort P5250A Series

Brand: Moxa Technologies Pages: 2

RS/6000 44P Series 270

Brand: IBM Pages: 346

MediaGrid ContentServer 3000

Brand: Omneon Pages: 2

Brand: IBM Pages: 82

Brand: Premio Pages: 2

ProLiant ML110 Gen 10

Brand: HPE Pages: 5

301269U - Ethernet Disk Mini Home Edition 500 GB Network Attached Storage Hard...

Brand: LaCie Pages: 74

Brand: NEC Pages: 138

Brand: Digi Pages: 126

Brand: Motorola Pages: 40

Brand: Motorola Pages: 90

Brand: XtendLan Pages: 27

Brand: Black Box Pages: 60

SuperStorageSystem SSG-2028R-DN2R24L

Brand: Supermicro Pages: 82

TwinPro 1029TP-DC0R

Brand: Supermicro Pages: 136

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands