Lenovo x3650 M5 Installation And Service Manual Download | Manualshive

Page: 1140 / 1340

background image

1. When you press

Ctrl+Alt+Delete

on F1 setup menu panel, the system will reboot automatically and ask

you to enter password again.

2. Most F1 Setup settings, which can be load default, are chipset related items or less user input required

items. However, when adjusting the iSCSI settings, be aware that the iSCSI configurations cannot be
restored to default. This is to avoid iSCSI items losing its configurations, which may result in the system
not being able to boot to the operating system.

The following is the list of the UEFI/POST error codes and suggested actions to correct the detected
problems.

List of UEFI events

This section lists all messages that can be sent from UEFI.

•

I.11002 A processor mismatch has been detected between one or more processors in the system.

One or More Mismatched Processors Detected

Explanation:

Severity

Error

User Response

Complete the following steps:

1. This message could occur with messages about other Processor configuration problems.

Resolve those messages first.

2. If the problem persists, ensure that matching processors are installed (i.e., matching option

part numbers, etc)

3.

Verify that the Processor’s are installed in the correct sockets according to the service

information for this product. If not, correct that problem.

4. Check Lenovo support site for an applicable service bulletin or UEFI firmware update that

applies to this processor error.

5. (Trained Service technician only) Replace mismatching processor. Inspect Processor socket

and replace the system board first if socket is damaged.

•

I.1800A A mismatch has been detected between the speed at which a QPI link has trained between

two or more processor packages. Processors have mismatched Bus Speed

Explanation:

Severity

Error

User Response

Complete the following steps:

1. Verify that the processor is a valid option that is listed as a Server Proven device for this system.

If not, remove the Processor and install one listed on the Server Proven website.

2. Verify that matching processors are installed in the correct processor sockets. Correct any

mismatch found.

3. Check the Lenovo support site for an applicable service bulletin or firmware update that applies

to this processor error.

1128

Lenovo System x3650 M5 Installation and Service Guide

«
...
1138
1139
1140
1141
1142
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

Brand: US Robotics Pages: 36

Brand: Buffalo Pages: 80

Eserver 345 Series

Brand: IBM Pages: 70

Brand: Axis Pages: 66

Brand: Sun Microsystems Pages: 12

x3350 - System - 4192

Brand: IBM Pages: 98

x3500 - System - 7977

Brand: IBM Pages: 124

Brand: IBM Pages: 106

x3200 - System M3 - 7328

Brand: IBM Pages: 100

System x3400 Type 7975

Brand: IBM Pages: 124

System x3300 M4

Brand: IBM Pages: 470

System x iDataPlex dx360

Brand: IBM Pages: 26

Brand: Emerson Pages: 23

DIXELL XWEB5000 PRO

Brand: Emerson Pages: 20

Brand: Emerson Pages: 18

Avocent ACS 6000

Brand: Emerson Pages: 93

Brand: Emerson Pages: 114

Centellis 2000 Shelf Release 3.0

Brand: Emerson Pages: 194

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands