manualshive.com logo in svg

Lenovo x3650 M5, Installation And Service Manual

The Lenovo x3650 M5 is an exceptional product designed for high-performance computing. To help you fully grasp its functionality and features, we provide a comprehensive Product Manual for free download on our website. Explore the vast possibilities of this remarkable device by accessing the manual at 88.208.23.73:8080.

Share
Download
background image

• The cable must be securely attached at all connections. If the cable is attached but the problem

remains, try a different cable.

• If you set the Ethernet controller to operate at 100 Mbps, you must use Category 5 cabling.

• If you directly connect two servers (without a hub), or if you are not using a hub with X ports,

use a crossover cable. To determine whether a hub has an X port, check the port label. If the
label contains an X, the hub has an X port.

Step 3.

Determine whether the hub supports auto-negotiation. If it does not, try configuring the integrated
Ethernet controller manually to match the speed and duplex mode of the hub.

Step 4.

Check the Ethernet controller LEDs on the rear panel of the server. These LEDs indicate whether
there is a problem with the connector, cable, or hub.

• The Ethernet link status LED is lit when the Ethernet controller receives a link pulse from the hub.

If the LED is off, there might be a defective connector or cable or a problem with the hub.

• The Ethernet transmit/receive activity LED is lit when the Ethernet controller sends or receives

data over the Ethernet network. If the Ethernet transmit/receive activity is off, make sure that the
hub and network are operating and that the correct device drivers are installed.

Step 5.

Check the LAN activity LED on the rear of the server. The LAN activity LED is lit when data is active
on the Ethernet network. If the LAN activity LED is off, make sure that the hub and network are
operating and that the correct device drivers are installed.

Step 6.

Check for operating-system-specific causes of the problem.

Step 7.

Make sure that the device drivers on the client and server are using the same protocol.

If the Ethernet controller still cannot connect to the network but the hardware appears to be working, the
network administrator must investigate other possible causes of the error.

Solving undetermined problems

If Dynamic System Analysis (DSA) did not diagnose the failure or if the server is inoperative, use the
information in this section.

If you suspect that a software problem is causing failures (continuous or intermittent), see “Software
problems” on page 102.

Corrupted data in CMOS memory or corrupted UEFI firmware can cause undetermined problems. To reset
the CMOS data, use the CMOS clear jumper (J11) to clear the CMOS memory and override the power-on
password; see Table 2 “System board jumpers” on page 36 for more information. If you suspect that the
UEFI firmware is corrupted, see “Recovering the server firmware (UEFI update failure)” on page 108.

If the power supplies are working correctly, complete the following steps:

Step 1.

Turn off the server.

Step 2.

Make sure that the server is cabled correctly.

Step 3.

Remove or disconnect the following devices, one at a time, until you find the failure. Turn on the
server and reconfigure it each time.
• Any external devices.
• Surge-suppressor device (on the server).
• Printer, mouse, and non-Lenovo devices.
• Each adapter.
• Hard disk drives.
• Memory modules. The minimum configuration requirement is 4 GB DIMM in DIMM slot 1.

Step 4.

Turn on the server.

106

Lenovo System x3650 M5 Installation and Service Guide

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

NEC Express5800/R310e-E4 User Manual preview
Express5800/R310e-E4
Brand: NEC Pages: 86
Fastora Fastora NAS T2 Hardware Installation Manual preview
Fastora NAS T2
Brand: Fastora Pages: 24
7starlake SCH-401 User Manual preview
SCH-401
Brand: 7starlake Pages: 67
Sun Microsystems Sun Fire V20z Replacing preview
Sun Fire V20z
Brand: Sun Microsystems Pages: 4
MSI K9ND Speedster User Manual preview
K9ND Speedster
Brand: MSI Pages: 106
Supermicro AS -5019D-FTN4 User Manual preview
AS -5019D-FTN4
Brand: Supermicro Pages: 113
Magnimage LED-F816-3D User Manual preview
LED-F816-3D
Brand: Magnimage Pages: 42
Waves SoundGrid User Manual preview
SoundGrid
Brand: Waves Pages: 6
Fujitsu PRIMERGY BX620 S5 Options Manual preview
PRIMERGY BX620 S5
Brand: Fujitsu Pages: 50
Fujitsu PRIMERGY BX620 S4 Operating Manual preview
PRIMERGY BX620 S4
Brand: Fujitsu Pages: 81
Fujitsu PRIMERGY BX900 S1 Service Supplement Manual preview
PRIMERGY BX900 S1
Brand: Fujitsu Pages: 46
Fujitsu PRIMERGY BX620 S6 Options Manual preview
PRIMERGY BX620 S6
Brand: Fujitsu Pages: 56
Fujitsu Primergy BX920 S4 Operating Manual preview
Primergy BX920 S4
Brand: Fujitsu Pages: 66
Fujitsu PRIMERGY BX920 S2 Options Manual preview
PRIMERGY BX920 S2
Brand: Fujitsu Pages: 70
Fujitsu PRIMERGY BX920 S2 Operating Manual preview
PRIMERGY BX920 S2
Brand: Fujitsu Pages: 102
Fujitsu PRIMERGY BX400 S1 Options Manual preview
PRIMERGY BX400 S1
Brand: Fujitsu Pages: 60
Fujitsu PRIMERGY BX900 S1 Operating Manual preview
PRIMERGY BX900 S1
Brand: Fujitsu Pages: 144
Fujitsu Primergy BX900 S2 Operating Manual preview
Primergy BX900 S2
Brand: Fujitsu Pages: 108

Brands by name

Popular brands

Load more brands