Lenovo x3650 M5 Installation And Service Manual Download

Page: 1206 / 1340

–

Latest level of DSA

–

Latest level of BMC/IMM

•

408-901-000 : MLNX:MLNX_DiagnosticTestIBPort Test Failed

Port Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Make sure that the physical link of the port under test in the active state and a subnet manager

running on the fabric to which the port is attached.

2. If these condition was met but the test keeps failing the port's adapter might be faulty.

3. Try replacing the adapter and repeating the test.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA memory isolation test results

The following messages can result when you run the memory isolation test.

Test results for the DSA memory isolation test

The following messages can result when you run the DSA memory isolation test.

•

201-000-000 : Standalone Memory Test Passed

Quick/Full Memory Test All CPUs Passed.

Recoverable

Severity

Event

Serviceable

1194

Lenovo System x3650 M5 Installation and Service Guide

«
...
1204
1205
1206
1207
1208
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands

Lenovo x3650 M5, Installation And Service Manual

Search results

Summary of Contents for x3650 M5

Reviews:

Related manuals for x3650 M5

Brands by name

Popular brands