Lenovo x3650 M5 Installation And Service Manual Download | Manualshive

Page: 18 / 1340

background image

•

Danger:

These statements indicate situations that can be potentially lethal or extremely hazardous

to you. A danger statement is placed just before the description of a potentially lethal or extremely
hazardous procedure step or situation.

Server features and specifications

The following information is a summary of the features and specifications of the server. Depending on the
model, some features might not be available, or some specifications might not apply.

Microprocessor (depending on the model):

• Supports up to two Intel Xeon E5-2600 v4 or Intel Xeon E5-2600 v3 series multi-core microprocessors

(one installed)

• Two QuickPath Interconnect (QPI) links speed up to 9.6 GT per second

Notes:

• Use the Setup Utility program to determine the type and speed of the microprocessors.

• For a list of supported microprocessors, see http://www.lenovo.com/ serverproven/.

• Read guidelines before installing or replacing the microprocessor. See “Replacing a microprocessor

and heat sink” on page 281.

Memory (depending on the model):

• Minimum: 8 GB
• Maximum: 1.5 TB

– 768 GB using registered DIMMs (RDIMMs)
– 1.5 TB using load reduction DIMMs (LRDIMMs)

• Type:

– PC4-19200 (DDR4-2400), operating speed depends on memory population
– Single-rank, dual-rank, or quad-rank
– Registered DIMM (RDIMM) or load reduced DIMM (LRDIMM)

• Slots: 24 dual inline
• Supports (depending on the model):

– 8 GB, 16 GB, and 32 GB RDIMMs
– 64 GB LRDIMMs

Note:

If your server comes with 2400 MHz momory modules and a CPU that supports a maximum of

2133 MHz memory, the data rate of your memory modules will be limited to 2133 MHz.

Integrated functions:

• Integrated management module 2.1 (IMM2.1), which consolidates multiple management functions

in a single chip.

• Broadcom BCM5719 Quad Port Gigabit Ethernet controller with Wake on LAN support
• Up to six Universal Serial Bus (USB) connectors (depending on the model)

– Three USB 2.0 connectors on the front of the chassis
– Two USB 3.0 connectors on the rear of the chassis
– One internal USB 2.0 connector used for Hypervisor USB key

• Four network ports (four 1 Gb Ethernet ports on the system)
• Supports one optional ML2 network daughter card
• One System Management RJ-45 on the rear to connect to a systems management network. This

system management connector is dedicated to the IMM2.1 functions.

• Optional serial port

Hard disk drive expansion bays (depending on the model):

• 2.5-inch models:

– Supports up to sixteen 2.5-inch simple-swap SAS/SATA hard disk drive bays.

6

Lenovo System x3650 M5 Installation and Service Guide

«
...
16
17
18
19
20
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

Brand: Fastora Pages: 24

Brand: 7starlake Pages: 67

System x3550 M3

Brand: IBM Pages: 160

System x3650 M4 Type 7915

Brand: IBM Pages: 192

Brand: IBM Pages: 694

System x3755 M3 7164

Brand: IBM Pages: 126

FusionServer 2298 V5

Brand: Fusion Pages: 89

Brand: Xerox Pages: 2

Brand: QNAP Pages: 69

Brand: 4xem Pages: 66

Brand: MRV Communications Pages: 65

Brand: Grafenthal Pages: 99

Brand: Digital Watchdog Pages: 7

Blackjack Tower DW-BJST51T Series

Brand: Digital Watchdog Pages: 14

Brand: Bosanova Pages: 2

Brand: Octagon Pages: 17

IP Video Surveillance

Brand: C-MOR Pages: 62

Brand: Wiredocean Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands