Lenovo x3650 M5 Installation And Service Manual Download | Manualshive

Page: 186 / 1340

background image

DIMM 3

DIMM 9

DIMM 6

DIMM 12

DIMM 2

DIMM 8

DIMM 5

DIMM 11

DIMM 1

DIMM 7

DIMM 4

DIMM 10

Microprocessor 1

CPU1

DIMM 15

DIMM 21

DIMM 18

DIMM 24

DIMM 14

DIMM 20

DIMM 17

DIMM 23

DIMM 13

DIMM 19

DIMM 16

DIMM 22

Microprocessor 2

CPU2

Figure 104. DIMM connectors location

DIMM installation sequence

Depending on the server model, the server may come with a minimum of one 4 GB DIMM installed in slot
1. When you install additional DIMMs, install them in the order shown in the following table to optimize
system performance.

In general, all four channels on the memory interface for each microprocessor can be populated in any order
and have no matching requirements.

Table 12. Normal mode DIMM installation sequence

Number of installed
microprocessor

DIMM connector population sequence

One microprocessor installed

1, 4, 9, 12, 2, 5, 8, 11, 3, 6, 7, 10

Two microprocessors installed

1, 13, 4, 16, 9, 21, 12, 24, 2, 14, 5, 17, 8, 20, 11, 23, 3, 15, 6, 18, 7, 19, 10, 22

For optimal performance:

Make sure all four memory channels of each microprocessor are populated. Each memory channels should
be populated with the same type and amount of memory per channel. Each microprocessor socket should
be populated with the same type and amount of memory per socket. 1DPC (one DIMM per channel) or
2DPC (two DIMM per channel) memory configuration are recommended. Unless there is a need for memory

174

Lenovo System x3650 M5 Installation and Service Guide

«
...
184
185
186
187
188
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

ALTOS R910 Series

Brand: Acer Pages: 74

Brand: Inspur Pages: 82

SuperServer 6026TT-HIBQF

Brand: Supero Pages: 112

Brand: Infrant Technologies Pages: 8

Brand: Sony Pages: 3

Brand: Sony Pages: 7

Brand: Sony Pages: 26

Brand: Sony Pages: 28

Brand: Sony Pages: 37

Brand: Sony Pages: 36

Brand: Sony Pages: 49

Brand: Sony Pages: 48

Brand: Sony Pages: 54

Brand: Sony Pages: 56

StorStation FSV-M3

Brand: Sony Pages: 78

Brand: Sony Pages: 106

Brand: Z Microsystems Pages: 22

ANTMAINER S19j Server

Brand: BITMAIN Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands