Lenovo x3650 M5 Installation And Service Manual Download | Manualshive

Page: 208 / 1340

background image

Step 4.

Remove the rear two hard-disk-drive kit that contains the adapter (see “Removing the rear two
hard-disk-drive kit” on page 207).

• If you are removing an adapter from PCI expansion slot 3, remove rear two hard-disk-drive kit 1.

• If you are removing an adapter from PCI expansion slot 8, remove rear two hard-disk-drive kit 2.

Step 5.

Disconnect any cables from the adapter (make note of the cable routing, in case you reinstall
the adapter later).

Step 6.

1

Slide the retention bracket; then,

2

rotate it to the open position.

1

3

2

Adapter

Adapter connector

Bracket

Rear two hard-disk-drive kit

Figure 130. Adapter removal

Step 7.

Remove the screws if present. These screws can be fastened to the side of the riser-card assembly
for storage if needed.

Step 8.

3

Carefully grasp the adapter by its top edge or upper corners, and pull the adapter out of the

rear two hard-disk-drive kit.

Step 9.

If you are instructed to return the adapter, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.

Replacing an adapter

Use this information to replace an adapter.

Notes:

• If your adapter was previously configured, backup or record its configuration information, if possible,

before replacing the adapter. See the documentation for your adapter for information and instructions.

• If you are replacing a ServeRAID adapter, import your RAID configuration to the replacement adapter as

a foreign configuration after you finish the replacement. See the

ServeRAID-M Software User Guide

https://support.lenovo.com/us/en/documents/migr-5086126 for instructions.

• The following adapters support 10-Gbps transfer rate only:

– Intel X710 2x10GbE SFP+ Adapter

– Intel X710 ML2 4x10GbE SFP+ Adapter

– Intel X710-DA2 ML2 2x10GbE SFP+ Adapter

Replacing an adapter in a riser-card assembly

Use this section to replace an adapter in a riser-card assembly.

196

Lenovo System x3650 M5 Installation and Service Guide

«
...
206
207
208
209
210
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

Brand: IBM Pages: 438

eServer 200 xSeries

Brand: IBM Pages: 128

eServer 232 xSeries

Brand: IBM Pages: 174

Brand: Lanner Pages: 43

Brand: AIC Pages: 112

UniServer T1100 G3

Brand: H3C Pages: 138

Brand: Data-Tronix Pages: 29

Brand: Data-Tronix Pages: 30

Brand: 7th Sense Pages: 156

Brand: Supero Pages: 112

Brand: Bosanova Pages: 2

Brand: Bosanova Pages: 2

Brand: Habey Pages: 3

Brand: Obvius Pages: 39

Brand: innuos Pages: 10

Brand: Terra Pages: 22

Brand: 360 Systems Pages: 148

Brand: B&B Electronics Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands