Lenovo x3650 M5 Installation And Service Manual Download | Manualshive

Page: 339 / 1340

background image

00

00

00

00

00

00

00

00

00

00

00

Figure 299. Front control panel assembly removal

Step 5.

Install the 2.5-inch advanced operation panel assembly. See “Replacing the media cage (also
called lightpath LCD operation panel assembly)” on page 184.

Step 6.

Install the top cover (see “Replacing the top cover” on page 151).

Step 7.

Slide the server into the rack.

Step 8.

Reconnect the power cords and any cables that you removed.

Step 9.

Turn on the peripheral devices and the server.

Updating the server configuration

Use this information to update the server configuration.

When you start the server for the first time after you add or remove a device, you might receive a message
that the configuration has changed. The Setup Utility starts automatically so that you can save the new
configuration settings.

Some optional devices have device drivers that you must install. For information about installing device
drivers, see the documentation that comes with each device.

If the server has an optional RAID adapter and you have installed or removed a hard disk drive, see the
documentation that comes with the RAID adapter for information about reconfiguring the disk arrays.

If you have installed a USB hypervisor memory key on the SAS riser-card, see the user's guide that comes
with the hypervisor memory key. Hypervisor enables guest operating systems to function on the server.

For information about configuring the integrated Gigabit Ethernet controller, see “Configuring the Ethernet
controller” on page 61.

Instructions for Business Partners

Instructions for Business Partners on verifying the newly installed devices by running the Dynamic System
Analysis (DSA) stress test.

In addition to the instructions in this chapter for installing optional hardware devices, updating firmware and
device drivers, and completing the installation, Business Partners must also complete the following steps:

Installing, removing, and replacing components

327

«
...
337
338
339
340
341
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

Brand: IBM Pages: 88

Brand: Digital Equipment Pages: 73

Brand: Belkin Pages: 2

Brand: Moxa Technologies Pages: 100

Brand: disguise Pages: 12

SPARC Enterprise M3000

Brand: Fujitsu Pages: 202

SPARC Enterprise M4000

Brand: Fujitsu Pages: 310

SPARC Enterprise M3000

Brand: Fujitsu Pages: 560

SPARC Enterprise M4000

Brand: Fujitsu Pages: 76

Brand: MO-SYS Pages: 26

Brand: Panasonic Pages: 17

Brand: Panasonic Pages: 42

Brand: Panasonic Pages: 316

Brand: Panasonic Pages: 456

SnapServer Expansion E2000

Brand: Overland Storage Pages: 5

Brand: Overland Storage Pages: 133

Brand: CasaTunes Pages: 7

ServTray KVT201A-JP-R3

Brand: Black Box Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands