Lenovo x3650 M5 Installation And Service Manual Download | Manualshive

Page: 58 / 1340

background image

Approximately 5 seconds after the server is connected to power, one or more fans might start running to
provide cooling while the server is connected to power and the power-on button LED will blink quickly.
Approximately 5 to 10 seconds after the server is connected to power, the power-control button becomes
active (the power-on LED will blink slowly), and one or more fans might start running to provide cooling while
the server is connected to power. You can turn on the server by pressing the power-control button.

The server can also be turned on in any of the following ways:

• If a power failure occurs while the server is turned on, the server will restart automatically when power

is restored.

• If your operating system supports the Wake on LAN feature, the Wake on LAN feature can turn on the

server.

Notes:

1. When 4 GB or more of memory (physical or logical) is installed, some memory is reserved for various

system resources and is unavailable to the operating system. The amount of memory that is reserved
for system resources depends on the operating system, the configuration of the server, and the
configured PCI options.

2. Ethernet 1 connector supports Wake on LAN feature.

3. When you turn on the server with the graphical adapters installed, the logo displays on the screen after

approximately 3 minutes. This is normal operation while the system loads.

Turning off the server

Use this information to turn off the server.

When you turn off the server and leave it connected to power, the server can respond to requests to the
service processor, such as a remote request to turn on the server. While the server remains connected to
power, one or more fans might continue to run. To remove all power from the server, you must disconnect it
from the power source.

Some operating systems require an orderly shutdown before you turn off the server. See your
operating-system documentation for information about shutting down the operating system.

Statement 5

CAUTION:
The power control button on the device and the power switch on the power supply do not turn off
the electrical current supplied to the device. The device also might have more than one power
cord. To remove all electrical current from the device, ensure that all power cords are disconnected
from the power source.

1

2

The server can be turned off in any of the following ways:

46

Lenovo System x3650 M5 Installation and Service Guide

«
...
56
57
58
59
60
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

Brand: PaloAlto Networks Pages: 30

Brand: Patton electronics Pages: 326

x3100 M5 Type 5457

Brand: IBM Pages: 688

Brand: B&B Pages: 55

Brand: IBM Pages: 66

Brand: TYANO Pages: 68

Snap! Server 4000

Brand: Quantum Pages: 8

Brand: Goonas Pages: 13

Brand: ASROCK Rack Pages: 51

Brand: TYAN Pages: 81

Alcatel-Lucent OXO Connect Compact

Brand: Nokia Pages: 216

Brand: Advantech Pages: 38

Brand: FreeNAS Pages: 4

Brand: Acnodes Pages: 5

Brand: Gateway Pages: 48

Brand: Inspur Pages: 63

Brand: Gigabyte Pages: 54

Brand: Sunfire Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands