Lenovo x3650 M5 Installation And Service Manual Download | Manualshive

Page: 94 / 1340

background image

• Checkpoint panel

• I2C bus

• SAS and SATA drives

If you are able to restart the server or if you need comprehensive diagnostics, use DSA Preboot.

For more information and to download the utilities, go to https://support.lenovo.com/us/
en/documents/LNVO-DSA.

Running the DSA Preboot diagnostic programs

Use this information to run the DSA Preboot diagnostic programs.

Note:

The DSA memory test might take up to 30 minutes to run. If the problem is not a memory problem,

skip the memory test.

To run the DSA Preboot diagnostic programs, complete the following steps:

Step 1.

If the server is running, turn off the server and all attached devices.

Step 2.

Turn on all attached devices; then, turn on the server.

Step 3.

When the prompt

<F2> Diagnostics

is displayed, press

F2

.

Note:

The DSA Preboot diagnostic program might appear to be unresponsive for an unusual

length of time when you start the program. This is normal operation while the program loads. The
loading process may take up to 10 minutes.

Step 4.

Optionally, select

Quit to DSA

to exit from the stand-alone memory diagnostic program.

Note:

After you exit from the stand-alone memory diagnostic environment, you must restart the

server to access the stand-alone memory diagnostic environment again.

Step 5.

Type

gui

to display the graphical user interface, or type

cmd

to display the DSA interactive menu.

Step 6.

Follow the instructions on the screen to select the diagnostic test to run.

If the diagnostic programs do not detect any hardware errors but the problem remains during normal server
operation, a software error might be the cause. If you suspect a software problem, see the information
that comes with your software.

A single problem might cause more than one error message. When this happens, correct the cause of the
first error message. The other error messages usually will not occur the next time you run the diagnostic
programs.

If the server stops during testing and you cannot continue, restart the server and try running the DSA
Preboot diagnostic programs again. If the problem remains, replace the component that was being tested
when the server stopped.

Diagnostic text messages

Diagnostic text messages are displayed while the tests are running.

A diagnostic text message contains one of the following results:

Passed:

The test was completed without any errors.

Failed:

The test detected an error.

82

Lenovo System x3650 M5 Installation and Service Guide

«
...
92
93
94
95
96
...
»

Summary of Contents for x3650 M5





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for x3650 M5

Express5800/T110g-S

Brand: NEC Pages: 34

Netfinity 6000R

Brand: IBM Pages: 218

eserver xSeries 440

Brand: IBM Pages: 74

eserver xSeries 440

Brand: IBM Pages: 98

eserver xSeries 440

Brand: IBM Pages: 84

Eserver xSeries 360 Type 8686

Brand: IBM Pages: 184

eserver xSeries 350

Brand: IBM Pages: 62

eServer xSeries 135

Brand: IBM Pages: 62

eserver pSeries 690

Brand: IBM Pages: 212

System x3690 X5

Brand: IBM Pages: 32

System x3690 X5

Brand: IBM Pages: 33

System x3690 X5

Brand: IBM Pages: 180

Brand: IBM Pages: 1032

Brand: IBM Pages: 98

Brand: IBM Pages: 70

SUPERSERVER 6015C-NT

Brand: Supermicro Pages: 110

x3350 - System - 4192

Brand: IBM Pages: 98

x3500 - System - 7977

Brand: IBM Pages: 124

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands