5
SNOOZE FUNCTION
PRESS “SNOOZE” BUTTON ON THE REMOTE CONTROL WHEN ALARM IN ACTIVE, ALARM WILL BE SLIENT
FOR 10 MINUTES. AFTER 10-MINUTUE SNOOZE INTERVAL, ALARM WILL BE ACTIVE AGAIN. SNOOZE CAN BE
USED FOR REPEATEDLY WITHIN THE 1-HOUR ALARM ACTIVE INTERVAL.
TIMER FUNCTION
1. PUSH THE POWER KNOB (18) TILL THE STANDBY INDICATOR (7) LIGHT OFF. UNIT IS TURNING FROM
STANDBY MODE TO OPERATION MODE.
2. WHEN THE UNIT IS IN OPERATION MODE, PRESS SLEEP BUTTONS (5) REPEATEDLY TO CHOOSE THE
SLEEP TIME MINUTES FROM 90>80>70…..>10 OFF.
3. SLEEP TIME SETTING IS STORED WHEN THE “SLEEP” ICON LIGHTS UP ON THE DISPLAY.
4. WHEN THE SLEEP TIME MINUTES IS OVER, UNIT WILL BE SWITCHED TO STANDBY MODE
AUTOMATICALLY.
LISTENING TO AM/FM RADIO
AM/FM RADIO TUNING
1. PRESS FUNCTION BUTTON (6) TO SELECT “TUNE” MODE.
2. SELECT THE DESIRED BAND BY RADIO BAND BUTTON (13) (AM OR FM).
3. TUNE TO THE REQUIRED STATION BY PRESSING SKIP UP
(15) OR SKIP DOWN
(14) BUTTON
FOR 1-2 SECONDS, AND THEN RELEASE.
4. THE UNIT WILL START SEEKING AUTOMATICALLY AND STOP WHEN A RADIO STATION IS FOUND.
MANUAL PRESET AM/FM RADIO STATIONS
1. WHEN THE DESIRED RADIO STATION IS FOUND, PRESS MODE BUTTON (3), PROGRAM NUMBER WILL
BE FLASHING.
2. PRESS PRESET UP (17) OR PRESET DOWN (16) TO CHOOSE THE PROGRAM NUMBER FOR STORING
THE DESIRED RADIO STATION.
3. PRESS MODE BUTTON (3) AGAIN TO CONFIRM, PROGRAM NUMBER WILL STOP TO FLASH.
4. REPEAT STEP 2 & 3 UNTIL ALL DESIRED RADIO STATIONS IS BEING FOUND AND STORED
5. PRESS PRESET UP (17) OR PRESET DOWN (16) TO CHOOSE THE PRESET RADIO STATIONS.
6. THE NUMBER OF STATIONS CAN BE FOUND AND STORED IS DEPENDED ON THE RECEPTION OF
DIFFERENT AREA AND COUNTRIES.
AUTO PRESET AM/FM RADIO STATIONS
1. DURING RADIO MODE, PRESS THE PLAY/PAUSE (2), THE UNIT WILL AUTOMATICLLY SCANS THE RADIO
FREQUENCY. WHEN THE CLEAR SIGNAL IS FOUND, IT WILL AUTOMATICALLY STORE THE RADIO
STATION, STARTING FROM PROGRAM NUMBER 1.
2. THE NUMBER OF STATIONS CAN BE FOUND AND STORED IS DEPENDED ON THE RECEPTION OF
DIFFERENT AREA AND COUNTRIES.
FM & FM-STEREO RECEPTION
PRESS “FM ST.” BUTTON ON THE REMOTE CONTROL TO SELTECT FM MONO OR FM STEREO MODE.
WHEN STEREO SIGNAL ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN MONO.
“ST” ICON LIGHT UP ON THE DISPLAY TO SHOW FM STEREO MODE IS RECEIVING.
HINTS FOR BETTER RECEPTION
1. AM: THERE IS A BUILT-IN AM BAR ANTENNA. IF AM RECECPTION IS WEAK, SLIGHTLY ROTATING OR
RE-POSITIONING OF THE UNIT WILL USUALLY IMPROVE THE AM RECEPTION.
2. FM : THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE
SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.
FM & FM-STEREO RADIO ENCODING
1. PRESS FUNCTION BUTTON (6) TO SELECT “TUNE” MODE AND SELECT THE DESIRED BAND BY RADIO
BAND BUTTON (13) (AM OR FM).
2. INSERT MEMORY DEVICE (USB DRIVE, SD OR MMC CARD)
3. PRESS THE “REC” BUTTON (4), IT WILL TAKE 3-5 SECONDS TO READ MEMORY DEVICE. THEN USB OR
SD ICON WILL BE FLASHING.
4. PRESS
SKIP UP
BUTTON (15) OR SKIP DOWN
BUTTON (14) TO SELECT DESIRED
MODE (USB OR SD) FOR ENCODING. THEN PRESS THE “REC” BUTTON (
4
) AGAIN TO
CONFIRM.
AND THE SYSTEM IS STARTING THE ENCODING MODE AFTER FEW SECONDSS.
5. IF ONLY USB DRIVE, SD OR MMC CARD IS INSERTED, STEP 4 CAN BE SKIPPED.
6. THE USB OR SD ICON WILL BE FLASHING ON THE DISPLAY DURNIG ENCODING.
7. TO FINISH ENCODING, PRESS
STOP
BUTTON
(13) AND DISPLAY WILL SHOW “END” AND RETURN
