background image

This documentation applies to the use of an MCH Series Variable Frequency Drive with LonWorks protocol and 
should  be  used  in  conjunction  with  the  MCH  Series  Installation  and  Operation  Manual  (Document  MH01)  that 
shipped with the drive. These documents should be read in their entirety as they contain important technical data 
and describe the installation and operation of the drive.

LON®, LonTalk® and LonWorks® are registered trademarks of the Echelon Corporation, San Jose CA 95126, 
http://www.echelon.com; support@echelon.com.

Anybus® and ABS-S® are registered trademarks of HMS Industrial Networks AB, Sweden, USA, Germany and 
other countries, http://www.anybus.com.

Modbus ™ is a registered trademark of Schneider Electric, founder of Modbus-IDA, http://www.modbus-IDA.org.

©  2003 AC Technology Corporation
No part of this documentation may be copied or made available to third parties without the explicit written approval 
of AC Technology Corporation. All information given in this documentation has been carefully selected and tested 
for compliance with the hardware and software described. Nevertheless, discrepancies cannot be ruled out. AC 
Tech does not accept any responsibility nor liability for damages that may occur. Any necessary corrections will be 
implemented in subsequent editions.

About These Instructions

Summary of Contents for LonWorks MCH Series




























Reviews: