Appendix
11-24
BA9300SU EN 2.1
Code
Important
Possible settings
LCD
Code
Important
Choice
Lenze
LCD
C0126
021,7 &(
3
0
Trip
2
Warning
3
Off
Conf. CE0
Configuration communication error monitoring
with automation interface CE0
C0130
DES 7J
g
NSET actual Ti times
C0134
5)* EID5DE
0
0/1
NSET RFG characteristic
Ramp characteristic for main setpoint
0: linear
1: S-shaped
C0135
&O1S5OM UO5'
0
0
{1}
65535
Control word
Controller control word for LECOM-A/B/LI or
operating module.
C0136
1
2
3
&75/:25'
&75/:25'
&75/:25'
g
Control word C135
Control word in DCTRL
Control word in CAN-IN1
Control word in AIF-IN
C0141
)&2'( RFSTDM
0.00
-199.99
{0.01 %}
199.99
Main setpoint
Used for relative analog signals. Used as main
setpoint in configurations C0005 = xxx1
C0142
6SD5S OPSJO1R
1
0
{1}
1
Start conditions are executed:
•
after mains connection
•
after message (t > 0.5s)
•
after trip
0
Start lock
1
Autostart
C0150
6SDS8R UO5'
g
0
{1}
65535
Status word when networked with automation
interfaces
•
Binary interpretation indicates the bit states
C0151
)'2 ':
g
Bit00
{01}
Bit 31
FDO signals (DW)
Display (hex.) of free digital outputs
•
Binary interpretation indicates the bit states
C0155
67$786 :25'
g
Bit00
{01}
Bit 15
Status word 2
Display (hex.) of free digital outputs
•
Binary interpretation indicates the bit states
[C0156]
1
2
3
4
5
6
7
67$7%
67$7%
67$7%
67$7%
67$7%
67$7%
67$7%
2000
5002
5003
5050
10650
505
500
→
Selection list 2
DCTRL-PAR*1-O
MCTRL-IMAX
MCTRL-MMAX
NSET-RFG I= O
CMP1-OUT
DCTRL-CW/CCW
DCTRL-RDY
STAT# (status word)
Configuration of the free bits of the status word
C0157
&
g
0
1
STAT# (status word)
Display of C0156
C0161
$ES S5JP
g
All fault indications
(see chapter 9.3)
Fault message TRIP
momentary fault indiations (as under C0168/1)
C0167
5FRFS GDJMNFN
0
0
No reset
1
Reset
History buffer reset
Clears the history buffer
C0168
1
2
3
4
5
6
7
8
)DJM 1O DES
)DJM 1O OM'
)DJM 1O OM'
)DJM 1O OM'
)DJM 1O OM'
)DJM 1O OM'
)DJM 1O OM'
)DJM 1O OM'
g
All fault indications
(see chapter 9.3)
History buffer number
•
List of faults occurred
History buffer
Faults are
1: active
2: last
3: last but one
4: last but three
5: last but four
6: last but five
7: last but six
8: last but seven
Summary of Contents for EVS9321-CS
