TOOL SPECIFICATIONS
MODEL OF TOOL ..................................................................
ZN-12M09
TOOL LENGTH ....................................................................... 9.06" (230 mm)
TOOL HEIGHT ........................................................................ 7.09" (180 mm)
TOOL WIDTH .......................................................................... 2.76" (70 mm)
WEIGHT (WITHOUT FASTENERS) ...................................…1.65 lbs (0.75 kg)
AIR INLET ............................................................................... 1/4" NPT
COMPRESSED AIR :
Maximum permissible operating pressure ............................. 110 PSIG (7.5 bar)
Recommended operating pressure range ........................….. 65
∼
90 PSIG (4.5
∼
6 bar)
AIR CONSUMPTION.............................................................. 0.0043 scfm with 25
nails per minute
@ 90 psi (6.2 bar)
Noise dB(A)
：
A-weighted sound pressure level LpA……………….……….. 80.52 dB(A)
A-weighted sound power level LwA………………….……..… 93.52 dB(A)
Measurement uncertainty: 3dB
Vibration (m/s
2
)
：
Hand-arm vibration value…………………………………..….. 1.9 m/s
2
Measurement uncertainty: 1.5 m/s
2
Warning:
The vibration emission during actual use of the power tool can differ from the declared total
value depending on the ways in which the tool is used; and of the need to identify safety
measures to protect the operator that are based on an estimation of exposure in the actual
conditions of use (taking account of all parts of the operation cycle such as the times when
the tool is switched off and when it is running idle in addition to the trigger time).
List of fasteners for ZN12M09
：
Crown Length
MAGAZINE
ψ
9.0 mm ,
ψ
0.35 "
9.0 mm ~ 16 mm , 0.35 " ~ 0.63 "
1 pcs
Foreword:
This pneumatic nailer is designed for using on soft material or driving tacks/decorative nails
into wood. Its well balanced, ergonomic and comfort non-slip cushioned grip ensure you a
satisfactory tackle and improve work efficiency. One of features is to drive different sizes of
loose nails. No more painful hammering.
Suitable applications:
Leather upholstery, shoes, antique, trimming mattresses
Caution:
Staplers are only applying on wood. Not suitable for stapling or nailing into concrete,
masonry bricks or steel. Do not fire if staples are jammed, as this will cause damage to the
relevant parts.
DANGER
Indicates an imminently hazardous situation which, if not avoided, will result in death or
serious injury.
WARNING
Indicates an potentially hazardous situation which, if not avoided, will result in death or
serious injury.
NOTE
Alerts the operator to useful information.
SAFETY INSTRUCTIONS
DANGER
1. Read this manual and understand all safety instructions before operation the tool. If you
have any questions, please contact our authorized representatives.
2. Only those fasteners listed in the operating instructions may be used in the fastener driv-
ing tools.
3. Only the main energy and the lubricants listed in the operating instructions may be used.
4. Fastener driving tools marked with an inverted equilateral triangle standing on one point
may only be used with an effective safety yoke.
5. Fastener driving tools equipped with contact actuation or continuous contact actuation,
marked with the symbol " Do not use on scaffoldings, ladders", shall not be used for spe-
cific application for example:
─
when changing one driving location to another involves the use of scaffoldings, stairs,
ladders, or ladder alike constructions, e.g. roof laths,
─
closing boxes or crates,
─
fitting transportation safety systems e.g. on vehicles and wagons.
6. For the maintenance of fastener driving tools, only spare parts specified by the manufac-
turer or his authorized representative shall be used.
7. Repairs shall carried out by agents authorized by the manufacturer or by other specialis-
ts, having due regard to the information given in the operating instruction.
8. Stands for mounting the fastener driving tools to a support for example a work table shall
be designed and constructed by the stand manufacturer in such a way that the fastener
driving tool can be safely fixed for the intended use, thus for example avoiding damage,
distortion or displacement.
9. Fastener driving tools operated by compressed air shall only be connected to compress-
ed air lines where the maximum allowable pressure cannot be exceed by a factor of
more than 10%, which can for example be achieved by a pressure reduction valve
which includes a downstream safety valve.
10. When using fastener driving tools operated by compressed air, particular attention must
be paid to avoid exceeding the maximum allowable pressure.
11. When using fastener driving tools operated by compressed air should only be operated
at the lowest pressure required for the work process at hand, in order to prevent unnece-
ssarily high noise levels, increased wear and resulting failures.
12. Hazards caused by fire and explosion when using oxygen or combustible gases for ope-
rating compressed air operated fastener driving tools.
13. Carry the fastener driving tool at workpiece using only the handgrip, and never with the
trigger actuated. Never carry the tool by the hose or pull the hose to move the tool.
14. Disconnect the tool from air supply before cleaning jams,
servicing, adjusting, and during non-operation.
15. Wear eye protection.
16. Do not use a check valve or any other fitting which allows
air to remain in the tool.
17. Do not place your hand or any part of your body in the
fastener discharge area of the tool when connecting or
disconnecting air supply.
18. Never point tool at yourself or at any other person.
AIR SUPPLY AND CONNECTION
NOTE
•
Many air tool users find it convenient to use oiler to help provide oil
circulation through tool and increase the efficiency and useful life
of the tool. Check oil level in the oiler daily.
•
Many air tool user find it convenient to use a filter to remove liquid
and impurities which can rust or wear internal parts of the tool. A
filter also increase the efficiency and useful of the tool. The filter
must be checked on a daily basis and if necessary drained.
•
For better performance, install a 3/8" quick connector (1/4" NPT
threads) with an inside diameter of .315" on your tool and a 3/8"
quick coupler on the air hose.
The following illustration shows the correct
mode of connection to the air
supply system which will increase the efficiency and useful life of
the tool.
LUBRICATION AND MAINTENANCE
NOTE
•
Disconnect the air supply from the tool before lubricating.
•
Your tool requires lubrication before you use it for the first time.
•
Wipe off excessive oil at the exhaust. Excessive oil will damage
O-rings of tool. If in-line oiler is used, manual lubrication through
the air inlet is not required on a daily basis.
•
Turn the tool so the inlet is facing up and put one drop of high
speed spindle oil, UNOCAL RX22, or 3-IN-1 oil into air inlet. Never
use detergent oil or additives. Operate the tool briefly after adding
oil.
c o n n e c to r
Q u ic k
Q u ic k
c o u p le r
R e g u la to r
c o u p le r
Q u ic k
c o n n e c to r
A ir h o s e
Q u ic k
O ile r
F ilte r
c o m p re s s o r
