background image

6.2.3 Self-test display mode

After the ULTRA Series UPS finishes a self-test, it will display :

6.2.3.1 A short beep and the one of Input Voltage Level lamps (no.4 -7) and

Load Level lamps (no.8-11) will lit that means the UPS is normal.

6.2.3.2 A long beep indicates that the UPS has detected something abnormal.

To mute the alarm, press the multi-function switch then observe the

error from the display :

The lamp no. 4 is lit when a stabilizer fault.

The lamp no. 5 is lit when a charger fault.

The lamp no.  6 is lit when a software failure.

The lamp no. 7 is lit when CPU error.

The lamp no. 8 is lit when an inverter fault.

The lamp no. 9 is lit when self-test is

cancelled because of battery power is too

low.

The lamp no. 11 is lit when it need to replace

the battery.

- 24 -

- 25 -

6.3 The meaning of  LCD display

6.3.1 Input Voltage Level Display

The symbol blinks twice every 1.5 seconds

when utility line voltage is very low.

The symbol is lit when utility line voltage is

low.

The symbol is lit when utility line voltage is

normal.

The symbol blinks twice every 1.5 seconds

when utility line voltage is high.

6.3.2 Load Level Display

The far-left bar is lit when loads are above 8%

(No load) and less than 25%.

Two bars are lit when loads are from 26% to

50%.

Three bars are lit when loads are from 51%

to 75%.

Four bars are lit when loads are from 76% to

100%.

All bars are lit and the far-right indicator blinks

when the connected loads are over 100%.

Summary of Contents for Ulta Series




















Reviews: