background image

LEROY-SOMER

Installation and maintenance

4291  en-10.2008/a

R220

A.V.R.

3 - INSTALLATION -

 

COMMISSIONING

3.1  - Electrical checks on the AVR

-  Check  that  all  connections  have  been 
made  properly  as  shown  in  the  attached 
wiring diagram.

-  Check  that  the  ST3  frequency  selection 

jumper is on the correct frequency setting.

-  Check  whether  the  ST4  jumper  or  the 
remóte  adjustment  potentiometer  have 
been connected.

3.2  - Settings

A

The  machine  is  tested  and  set  at  the 
factory.  When  firs t  used  with  no  load, 

make sure that the drive speed is correct 

and  stable  (see  the  nameplate).  After 
operational  testing,  replace  all  access 
panels or covers.

The  only  possible  adjustments  to  the 

machine should be made on the AVR.

3.2.1  - R 220 setting (shunt system)

Initial potentiometer settings

-Plpotentiometer(AVRvoltageadjustment): 

fully anti-clockwise.

- Remóte voltage adjustment potentiometer: 
centre position.

Run the alternator at its rated  speed.  If the 

voltage  does  not  increase,  the  magnetic 
circuit should be remagnetized (see section 
3.3).

-  Turn  the  AVR  voltage  adjustment 
potentiometer  P1  slowly  until  the  output 

voltage rated valué is obtained.

- Adjust the stability setting using P2. 

Clockwise: increase the rapidity. 

Anti-clockwise: decrease the rapidity.

3.2.2  - Special type of use 

(  W A R N IN G   )

Excitation circuit E+,  E- must not be left 

open when the machine is running : AVR 
damage w ill occur.

3.2.1.1  - R220 field weakening (SHUNT)

<rfc>—

o

r

VOLT  P0T1K 

110  0 v   E +   E -

*  i i [ i  

E 3 H in n

The exciter is switched off by disconnecting 
the AVR power supply (1  wire - 0 or 110V). 
Contact rating  : 16A - 250V alt.

3.2.1.2 - R220 field forcing

(400V-10A)

Diode

&

Battery must be isolated from  the earth.

&

Exciter field may be at line potential.

Summary of Contents for R220 VSG+CCM









Reviews: