background image

Shanghai Jianghuai Environmental Equipment Co.,LTD

12

□Check the wear condition of brush.

Operating machine

1. Key to turn on the main power supply to (I) position.

2. The squeegee lift lever to pull down, so that the squeegee assembly lowered to the ground.

3. On the brush head lifting pedal, make the brush head fell to the ground.

4.Open the water control knob.

5.Press the brush plate motor switch, then press the suction motor switch.

6.Motor drive models: The speed control knob to your desired cleaning speed

Note: We recommend the use of 45-60 meters per minute cleaning speed.

During operation of the machine

WARNING: Fire or explosion hazard. Do not pick up flammable materials or reactive metals.

1. Each channel overlap 5 cm cleaning path.

2. The machine continues to avoid damage to the ground.

3. Such as squeegee absorbing water, the ground drag marks, wipe with a cloth tape to remove

garbage. Prior produce clean to prevent drag marks.

4. Do to the slope exceeds 5% (3 °) slope to operate the machine.

FOR SAFETY: When using machine, on slopes and slippery surface of the ground, move slowly.

5. If too much foam, will recommend the use of anti-foaming agent solution was poured into

water tank.

Note: Do not allow foam to enter the filter, in order to avoid damage to the vacuum motor. Foam

will filter switch does not fail.

6. Use double cleaning method to clean heavily soiled areas. First squeegee lifted for cleaning, let

the impregnation solution 3-5 minutes, will lower the squeegee and clean again.7. Depending on

the need to replace or rotate scouring pad.

8. Observe the battery power consumption table (refer "Battery power table").

Summary of Contents for SJ-460



































Reviews: