background image

 p

arTS

 i

denTifiCaTiOn

Parts List Overview

Item Description

  A  Floor and Sidewall Trailer Body Panels 

 

  B  5 x 4.5 Lug Pattern Torsion Axle with  

 

Autolube Fitting 

  C  Fenders 

  D  2" A-Frame Coupler 

  E  Safety Cables 

  F  84" x 1.625" C-Channels 

 G  56" x 23" U-Tubes 

  H  84" x 2" x 2" Frame Tubes  

  I 

55" x 2" x 2" A-Frame Tubes  

  J  2" x 2" x 48" Frame Angle  

  K  13" Tire & Wheel Assembly ST 175/80D13  

 

Tire & Wheels 

  L  Stud Mount Passenger Tail Light  

 

without License Illuminator 

 M  Stud mount Driver Tail Light  

 

with License Illuminator 

  N  Amber Lights, Front Marker Light 

 O  L-Bend Bolt On Light Brackets 

 

  P  License Plate Triangular Plate 

 Q  4-Flat Wire Lighting Harness with  

 

Four-Flat Connector 

  R  End Gates 

  S  5/16”  Snap Pins 

  T  1-1/2" Wide End Gate Support L-Brackets 

 

(Fits Inside Trailer Frame Tube) 

  U  1" Wide Steel Angle End Gate Latch 

 

(Fits Trailer Body) 

  V  2" Wide Steel Angle Body Latch 

 

(Fits End Gates) 

 W  Self Drilling Screws

 

X&Y  Spring Nut, L-Bracket, Hardware Kit:

   Front

   

X   5/16” Spring Nuts, 1/2” Spring Nut with 5/16” X 2”  

     Bolts, 1/2” X 1” Bolts, Spring Nut Holder 

   

     and Washers

   Rear

   

Y   5/16” Spring Nuts with 5/16” X 2” Bolts, Washers,          

     Split Ring Lock Washers

   

End Gate Support L Bracket

A

A

S

C

M

C

Q

T

X & Y

X & Y

RR

R

R

U

Z

AA

W

RR

LL 

CC

Y

BB

V

MM

T

Page 9 of 21

Summary of Contents for LittleGiant Trailer TLK864






















Reviews: