LeuchtKraft ODC-100/RGB Instruction Manual Download

Page: 14 / 80

Deutsch
Deutsch Seite

Français
Français Page

Italiano
Italiano Pagina

Nederlands
Nederlands Pagina

Español
Español Página

Polski
Polski Strona

English
English Page

English

1 Applications

. . . . . . . . . . . . . . 14

2 Safety Notes

. . . . . . . . . . . . . 14

3 Setting the Spotlight into Operation

. . 15

3.1 Installation

. . . . . . . . . . . . . . . 15

3.2 Barn doors

. . . . . . . . . . . . . . . 15

3.3 Power supply

. . . . . . . . . . . . . . 15

3.3.1 ODC-100 / RGB

. . . . . . . . . . . . . 15

3.3.2 PARC-100 / RGB

. . . . . . . . . . . . 16

4 Operation

. . . . . . . . . . . . . . . 16

4.1 Independent operation

. . . . . . . . . . 16

4.1.1 Colour spotlight and stroboscope

. . . . . 16

4.1.2 Different shades of white

Storing 11 shades of colour

. . . . . . . 16

4.1.3 Music control

. . . . . . . . . . . . . 17

4.1.4 Show programmes and sequences of scenes

4.1.5 Programming sequences of scenes

. . . . . 17

4.2 Synchronous control of multiple spotlights

(master / slave mode)

. . . . . . . . . . . 18

4.3 Operation with a DMX controller

. . . . . . 18

4.3.1 Connection

. . . . . . . . . . . . . . 18

4.3.2 Setting the number of DMX channels

. . . 19

4.3.3 Setting the DMX start address

. . . . . . 19

4.3.4 Using subaddresses

. . . . . . . . . . . 20

4.3.5 Functions of the DMX channels

. . . . . . 21

5 Additional Functions

. . . . . . . . . . 21

5.1 Maximum brightness of the spotlight

. . . . 21

5.2 White balance

. . . . . . . . . . . . . . 22

5.3 Slow response of the LEDs

. . . . . . . . 22

5.4 Resetting the spotlight to its factory settings

. 23

6 Cleaning the Spotlight

. . . . . . . . . 23

7 Specifications

. . . . . . . . . . . . . 23

DMX LED Spotlight

These instructions are intended for users with
basic knowledge in DMX control . Please read the
instructions carefully prior to operation and keep
them for later reference .

On page 2, you will find the spotlights ODC-

100 / RGB and PARC-100 / RGB . The menu for the
settings of the spotlight can be found on pages
78 and 79 .

Contents

1 Applications

This LED spotlight is used for illumination, e . g .
on stage, in discotheques and function rooms .
The light source is a powerful COB LED (COB =
chip-on-board technology): Many individual LED
chips are densely packed on a PCB to provide a
uniform light distribution .

The spotlight is designed for control via a

DMX light controller (3, 4, 5 or 10 DMX con-
trol channels), but it can also be operated in-
dependently without a controller . The ODC-
100 / RGB is weatherproof (IP 66) and therefore
also suited for outdoor applications .

2 Safety Notes

The spotlight corresponds to all relevant directives
of the EU and is therefore marked with .

WARNING

The spotlight uses dangerous
mains voltage . Leave servicing to
skilled personnel; inexpert han-
dling may result in electric shock .

•

The spotlight PARC-100 / RGB is suitable for
indoor use only . Protect it against dripping
water and splash water, high air humidity and
heat (admissible ambient temperature range:
0 – 40 °C) .

The spotlight ODC-100 / RGB is suitable for out-
door applications (admissible ambient temper-
ature range: −20 to +40 °C) .

•

Immediately disconnect the mains plug from
the socket
1 . if the spotlight or the mains cable is visibly

damaged,

2 . if a defect might have occurred after the

spotlight was dropped or suffered a similar
accident,

3 . if malfunctions occur .
In any case the spotlight must be repaired by
skilled personnel .

•

Never pull the mains cable to disconnect the
mains plug from the socket, always seize the
plug .

•

For ODC-100 / RGB only: A damaged mains
cable must be replaced by skilled personnel
only .

•

No guarantee claims for the spotlight and no
liability for any resulting personal damage or
material damage will be accepted if the spot-
light is used for other purposes than originally