background image

 

 

8

heat and dust. Use only 1 or 2 shots with a hand gun in most cases. Maximum handgun rating 40 P.S.I.  

 
Table #3 

  

 

Conditions Around Bearing

 

Operating Temperature of Fan

 

**Greasing Intervals

 

Fairly Clean 

up to 120 °F 

6-12 months 

 120°-160°F 

2-3 

months 

 

160°-200°F plus* 

1-2 months 

Moderate to 

up to 160°F 

1-2 months 

Extremely Dirty 

160°-200°F plus* 

2-4 weeks 

Cold Storage Room 

 

every defrosting period or 

 

 

no more than 4 months 

 

* For fan applications over 200°F: greasing intervals should be from several days to 2 weeks, depending on 
the temperature.  

** For vertical installations, greasing intervals should be twice as frequent as table values.  
 
The following greases, or one that is equivalent to the general description, are recommended for the 
following temperatures or excessive moisture applications.  

Operating Conditions

 

Use Grease Equivalent to these Grades

 

 

Esso-Beacon #325 (-65°F) 

Temperatures -65°F to 0°F  

Mobil Grease #28 (-65°F) 

 

Shell Oil Aeroshell No. 7 (-100°F)  

General Description:  Versatile  multipurpose  microgel thickened synthetic hydrocarbon grease with 
corrosion inhibitors, anti-oxidant additives, water resistance tendencies and EP characteristics.  

 

Temperature 0°F to 200°F inclusive  

Mobil Oil - Mobilux EP #2  

(Also use for heavy condensation  

Shell Oil - Shell Alvania EP #2  

or direct splash of water)  

Chevron - Chevron SRI #2  

 
General Description: Multipurpose NLGI#2 grease from lithium soap with EP characteristics, rust inhibitors, 
anti-oxidant additives and good water resistance tendencies.  

 

Temperatures over 200°F 

Dow  Corning-DC44  (400°F) (Not compatible with non-silicon 
based greases)  

 

General Description:  Versatile  multipurpose microgel thickened synthetic hydrocarbon grease with 

corrosion inhibitors, anti-oxidant additives, water resistance tendencies and EP 
characteristics.  

 

WARRANTY 

 

Lev-co warrants products of its own manufacture against defects of material and workmanship under 

normal use and service for a period of (12) months. This warranty does not cover ordinary wear and tear, 
abuse, misuse, overloading, negligence, alteration or systems and/or materials not of Seller’s manufacture. 
Expenses incurred by Buyer(s) in repairing or replacing any defective product will not be allowed except 
where authorized in writing and signed by an officer of the Seller.  

Summary of Contents for SQBI














Reviews: