background image

 

 
 
 
 

FCC MARKING 

 

This Equipment has been tested and found to comply with the limits for a  Class A  
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection  against harmful interference when  the  equipment  is 
operated in a commercial environment. This equipment generates, uses, and can radiate 
radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio  communications. 

 

Operation of this equipment in a  residential area is likely to cause  harmful interference 
in which case the user will be required to correct the interference at his own expense.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the   
following two conditions: (1)  this device may not cause harmful interference, and (2)  
this device must accept any interference received; including interference that may cause 
undesired operation. 

 
 

 

CE MARKING 

 

This equipment complies with the requirements relating to electromagnetic 
compatibility, EN 55022 class A for ITE, the essential protection requirement of  
Council Directive 2004/108/EC on the approximation of the laws of the Member States 
relating to electromagnetic  compatibility. 

 

Company has an on-going policy of upgrading its products and it may be possible that 
information in this document is not up-to-date. Please check with your local distributors for the 
latest information. No part of this document can be copied or reproduced in any form without 
written consent from the company. 

 

Trademarks: 
All trade names and trademarks are the properties of their respective companies. 

 
 
 
 
 

 

Copyright ©  2013, All Rights Reserved. 

Summary of Contents for IGP-0102

















Reviews: