WIRELESS 30A LOAD CONTROL MODULE
Cat. No. 73A00-3ZB
Installation Instructions and User’s Guide
INSTALLATION
ENGLISH
DI-021-ZI733-00A
AR2253
DI-021-ZI733-00A
AR2253
© 2013 Leviton Mfg. Co., Inc.
DESCRIPTION
The Model 73A00-3ZB Wireless 30A Load Control Module (LCM) can be used to
control water heaters, pool pumps, outdoor fountains, lighting, and much more.
ENROLLING THE 73A00-3ZB LCM TO ZIGBEE NETWORK
Confirm that the LCM is currently not enrolled in the network (i.e. blinking 1/Second at
50% On). If the LCM is enrolled in the network, disband LCM.
1) Place the supplied magnet on LCM near the magnetic sensor until the LED
changes to blinking 7 times per second. This will require that the magnet be held at
this location for 5+ seconds.
2) Enroll the device using the ZigBee Interface Module (ZIM).
3) Verify device was enrolled properly by checking to see if the LED is blinking 1 time
a second at 10% On (Normal operation).
DISBANDING THE 73A00-3ZB LCM FROM ZIGBEE NETWORK
1) Confirm LCM is currently in network (i.e. any LED state except blinking 1/Second
at 50% On).
2) Place magnet on LCM near magnetic sensor and hold at this location for 6-8
seconds.
3) Remove magnetic from magnetic sensor for 6-8 seconds.
4) Place magnetic on LCM near magnetic sensor and hold at this location for 6-8
seconds, until the LED changes to blinking 1/Second at 50% On.
5) Device is disbanded.
As per SIPCO LLC, this product may be used in a system and employs certain elements from one or
more of the following U.S. Patents: IP CO, LLC: 7,089,125; 7,054,271; 6,249,516; 6,044,062. SIPCO LLC:
7,103,511; 6,914,893; 6,891,838; 5,714,931; 6,233,327; 7,397,907; 6,618,578; 7,079,810; 7,295,128;
7,263,073; 7,480,501; 6,437,692; 7,468,661; 7,053,767; 7,650,425; 7,739,378
This device is intended for installation in accordance with the National Electrical
Code and local regulations. It is recommended that a qualified electrician perform
this installation. Retain these instructions for future reference.
This product is suitable for indoor or outdoor use.
BLACK / WHITE
100-250VAC, 50/60 Hz
POWER SUPPLY:
CONNECT TO "ALWAYS ON" CIRCUIT
POWER .35W STANDBY; .95W ACTIVE
ORANGE
SWITCHED CONTROL CIRCUIT
30A @ 240VAC GEN PURPOSE
2HP @ 240VAC
1HP @ 120VAC
THIS SIDE UP
LED INDICATOR
BLACK
WHITE
30A @ 28VDC GEN PURPOSE
USE APPROPRIATE SCREWS (NOT PROVIDED)
TO MOUNT UNIT, DO NOT OVER-TIGHTEN
FOR BEST RF PERFORMANCE, MOUNT TO NON-METALLIC
SURFACE, OR MOUNT WITH TOP OF UNIT 1.5 INCHES OR
MORE ABOVE METALLIC SURFACE
1.5" MIN
EXAMPLE
WARNINGS AND CAUTIONS
•
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or
fuse and test that power is off before wiring!
• If you are unsure about any part of these instructions, consult an electrician.
• SAVE THESE INSTRUCTIONS.
WARNINGS AND CAUTIONS
• To be installed and/or used in accordance with appropriate electrical codes and
regulations.
• Use this device with
copper or copper-clad wire only.
• For indoor use only.
(73I00-3ZB)
WEB VERSION
www.
GlobalTestSupply
.com
Find Quality Products Online at:
sales@GlobalTestSupply.com
