3-Way Wiring - Digital/Smart Switch with DD0SR-DLZ
Switching Remote Application:
3-Way Wiring - Digital/Smart Dimmer with DD00R-DLZ Dimming
Remote Application:
NOTE: Installation must be compliant with dimmer load ratings.
PK-A3123-10-00-2B
TOOLS NEEDED TO INSTALL YOUR REMOTE
Slotted/Phillips Screwdriver
Electrical Tape
Pliers
Pencil
Cutters
Ruler
INSTALLING YOUR REMOTE
NOTE: Use check boxes when Steps are completed.
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
WARNING:
TO AVOID FIRE, SHOCK OR DEATH; TURN
OFF POWER at circuit breaker or fuse and test that power
is off before wiring!
Step 1
INTRODUCTION
Decora Digital/Decora Smart Matching Dimmer or Switch Remote is designed to be used
for multi-location control of Leviton’s line of Decora Digital and Decora Smart Dimmers or
Switches allowing the lighting to be controlled from the main control or the remote location.
It works using digital circuitry that provides soft fade on/fade off, intuitive operation and a
stylish form factor that is compatible with Leviton’s Decora wallplates (sold separately).
White face assembled on device with ivory and light almond face plates included.
• ON/OFF LED
• Three way communication
• Ease of installation – No new wiring
FEATURES
Side Wire Connection
Side wire terminals accept #14-12 AWG
solid copper wire only.
Back Wire Connection
Back wire openings accept #14-12 AWG
solid copper wire only.
Preparing and connecting wires:
This remote can be wired using side wire terminal screws or through
backwire openings.
Step 3
5/8"
(1.6 cm)
Strip Gage
(measure bare
wire here)
3-Way or More Applications (Multi-location)
Universal Matching Remotes (Dimming and Switching)
Cat. No. DD00R-DLZ - Matching Dimming Remote - 120/277VAC, 60Hz
Cat. No. DD0SR-DLZ - Matching Switching Remote - 120/277VAC, 60Hz
INSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS:
• TO AVOID FIRE, SHOCK OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!
• To be installed and/or used in accordance with electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• Decora
®
Digital/Decora Smart remotes are not compatible with standard 3-way or 4-way switches. They must be used with compatible Decora Digital/
Decora Smart devices for multi-location switching.
WARNINGS AND CAUTIONS:
• Use this device WITH COPPER OR COPPER CLAD WIRE ONLY.
• Use only one (1) Decora Digital/Decora Smart dimmer or switch in a multi-location circuit with up to 4 matching remotes.
NOTE: The remote(s) will turn the light on at the brightness level selected at the dimmer.
• Recommended minimum wall box depth for remotes is 2-1/2".
• Maximum wire length from switch to all installed remotes cannot exceed 300 ft (90 m).
6
5
4
1
2
3
2
5
4
3
1
4-Way
1. First Traveler (note color)
2. Second Traveler (note color)
3. Neutral
4. Ground
5. Third Traveler (note color)
6. Fourth Traveler (note color)
NOTE: The first and third traveler
wires are used to carry line power
to the other switch boxes.
3-Way
1. Line or Load (Tagged)
2. Neutral
3. Ground
4. First Traveler (note color)
5. Second Traveler (note color)
NOTE: The first traveler wire is
used to carry line power to the
other switch box.
Identifying your wiring application
(most common):
NOTE: If the wiring in the wall box does not resemble
any of these configurations, consult an electrician.
Step 2
IMPORTANT:
For 3-Way applications, note that one of the screw terminals from the old switch being
removed will usually be a different color (Black) or labeled Common. Tag that wire with
electrical tape and identify as the common (Line or Load) in both the dimmer/switch wall
box and remote wall box.
For 4-Way applications, note that the old switch being removed will have 4 screws
plus a ground screw. Tag the two wires connected to the two back screw terminals.
Changing the color of your Remote:
Your remote may include color options. To change color of the face proceed as follows:
1
2
Insert top tabs
and press in
bottom tabs to
attach
Push in sides at
bottom tabs and
pull outward to
release
• Make sure that the ends of the wires from the wall box are straight (cut if necessary).
• Remove insulation from wires in the wall box as shown.
Cut
(if necessary)
Step 4a
NOTE: DDL06, DDMX1, DDE06, DD710, DW6HD, DW1KD, DH6HD, DH1KD, DZ6HD,
DZ1KD, DL6HD and DL1KD are compatible with DD00R-DLZ.
NOTE: The Digital/Smart Dimmer must be installed in a wall box that has a Load connection.
The DD00R-DLZ dimming remote must be installed in a wall box with a Line Hot connection
and a Neutral connection.
WIRING DD00R-DLZ DIMMING REMOTE
(wall box with Line Hot connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: Use backwire connection when connecting two wires to one screw terminal.
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing old switch and First
Traveler (note wire color) to remote terminal screw marked "BK".
• Second Traveler wall box wire to remote terminal screw marked "YL/RD" (note wire
color). This traveler from the remote must go to Yellow/Red dimmer lead.
• Neutral wall box wire to remote terminal screw marked "WH".
WIRING DIGITAL/SMART DIMMER (wall box with Load connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green dimmer lead.
• Load wall box wire identified (tagged) when removing old switch to the Red dimmer lead.
• First Traveler (color noted above) to the Black dimmer lead.
• Remove Red insulating label from the Yellow/Red dimmer lead.
• Second Traveler wall box wire (color noted above) to Yellow/Red dimmer lead. This
traveler from the dimmer must go to the terminal screw on the remote marked "YL/RD".
• Neutral wall box wire to White dimmer lead.
• Proceed to Step 5.
Hot (Black)
Neutral (White)
Digital/Smart Dimmer
DD00R-DLZ
Dimming Remote
YL/RD
Red
Yellow/
Red
WH
BK
Black
Black
White
Line
120VAC
60Hz
White
Load
Green
Ground
Green
Ground
Digital/Smart Dimmer
White
Red
Green
Black
1
2
3
Yellow/Red
4
5
DD00R-DLZ
Dimming Remote
Neutral to Terminal
Screw marked
White (WH)
2
3
5
WH
BK
YL/RD
4
1
Terminal
Screw
marked
Black
(BK)
Terminal
Screw
marked
Yellow/
Red
(YL/RD)
Step 4b
NOTE: DDS15, DW15S, DH15S, DZ15S and DL15S are compatible with DD0SR-DLZ.
NOTE: The Digital/Smart Switch must be installed in a wall box that has a Load
connection. The DD0SR-DLZ switching remote must be installed in a wall box with a
Line Hot connection and a Neutral connection.
WIRING DD0SR-DLZ SWITCHING REMOTE
(wall box with Line Hot connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: "RD" terminal on switching remote is unused. Tighten screw.
NOTE: Use backwire connections when connecting two wires to one screw terminal.
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing old switch and
First Traveler (note wire color) to remote terminal screw marked "BK".
• Second Traveler wall box wire to remote terminal screw marked "YL/RD" (note wire
color). This traveler from the remote must go to the terminal screw on the switch
marked "YL/RD".
• Neutral wall box wire to remote terminal screw marked "WH".
WIRING DIGITAL/SMART SWITCH (wall box with Load connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to switch terminal
screw marked "RD".
• First Traveler (color noted above) to switch terminal screw marked "BK".
• Remove Red insulating label from terminal screw marked "YL/RD".
• Second Traveler wall box wire (color noted above) to switch terminal screw marked
"YL/RD". This traveler from the switch must go to the terminal screw on the remote
marked "YL/RD".
• Proceed to Step 5.
Digital/Dimmer Switch
DD0SR-DLZ
Switching Remote
Terminal
Screw
marked
Black
(BK)
Terminal
Screw marked
Red (RD)
Terminal
Screw marked
White (WH)
Terminal
Screw
marked
Yellow/
Red
(YL/RD)
2
3
5
Neutral to Terminal
Screw marked
White (WH)
2
3
5
WH
BK
YL/RD
WH
BK
RD
YL/RD
1
4
4
1
Terminal
Screw
marked
Black
(BK)
Terminal
Screw
marked
Yellow/
Red
(YL/RD)
Hot (Black)
Neutral (White)
Load
YL/RD
YL/RD
RD
BK
Black
White
Line
120/277VAC
60Hz
WH
BK
WH
DD0SR-DLZ
Switching Remote
Digital/Smart Switch
Green
Ground
Green
Ground
