Testing your Switch prior to mounting in wall box:
Switch Mounting:
TURN OFF POWER AT
CIRCUIT BREAKER OR FUSE.
3-Way Wiring with DD0SR-DL Matching Remote
(with LED) Application:
DI-000-DDS15-02A
• Restore power at circuit breaker or fuse.
• Press pad until locator light is OFF. Lights
should turn ON.
If lights do not turn ON, refer to the
TROUBLESHOOTING section.
Step 5
For additional information, contact Leviton’s
Techline at 1-800-824-3005 or visit Leviton’s
website at www.leviton.com
• Position all wires to provide room in outlet
wall box for device.
• Ensure that the word “TOP” is facing up on
device strap.
• Partially screw in mounting screws in wall
box mounting holes.
NOTE:
Dress wires with a bend as shown
in diagram in order to relieve stress when
mounting device.
Step 6
Installation may now be completed by tightening
mounting screws into wall box. Attach wallplate.
Restore Power:
Restore power at circuit breaker or fuse.
Installation is complete.
Step 7
Step 4c
Switch
Matching Remote (with LED)
Terminal
Screw
marked
Black
(BK)
Terminal
Screw marked
Red (RD)
Terminal
Screw marked
White (WH)
Terminal
Screw
marked
Yellow/
Red
(YL/RD)
Terminal
Screw marked
Red (RD)
2
3
5
Neutral to Terminal
Screw marked
White (WH)
2
3
5
WH
BK
RD
YL/RD
WH
BK
RD
YL/RD
1
4
4
1
Terminal
Screw
marked
Black
(BK)
Terminal
Screw
marked
Yellow/
Red
(YL/RD)
Hot (Black)
Neutral (White)
Load
YL/RD
YL/RD
RD
BK
Black
White
Line
120/277 VAC
60Hz
WH
BK
WH
Matching Remote (with LED)
Switch
Green
Ground
Green
Ground
RD
(unused)
NOTE:
The switch
must
be installed in a wall box that has a Load
connection. The matching remote must be installed in a wall box with
a Line Hot connection and a Neutral connection. A Neutral wire to the
matching remote needs to be connected as shown.
If you are unsure about any part of these instructions, consult an
electrician.
NOTE:
Maximum wire length from switch to all installed remotes cannot
exceed 300 ft (90 m).
WIRING MATCHING REMOTE (wall box with line hot
connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE:
"RD" terminal on matching remote is unused. Tighten screw.
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing
old switch and First Traveler to Remote terminal marked BK.
• Second Traveler wall box wire from switch to remote terminal screw
marked "YL/RD"
(note wire color)
. This traveler from the remote must
go to Yellow/Red switch terminal screw.
• Line Neutral wall box to remote terminal screw marked "WH".
WIRING SWITCH (wall box with load connection):
Connect wires per WIRING DIAGRAM as follows:
• Green or bare copper wire in wall box to Green terminal screw.
• Load wall box wire identified (tagged) when removing old switch to
Red terminal screw.
• First Traveler Line Hot to Black terminal screw.
• Remove Red insulating label from Yellow/Red terminal screw.
• Second Traveler wall box wire
(note color as above)
to Yellow/Red
terminal screw. This traveler from the switch must go to the terminal
screw on the remote marked "YL/RD".
• Line neutral wall box wire to White terminal screw.
•
Proceed to Step 5.
© 2015 Leviton Mfg. Co., Inc.
NOTE:
The locator light will illuminate when the load is in the OFF position
to facilitate access in the dark.
Push Pad (Default settings)
Turn ON from OFF position:
Tap top of rocker – Lights turn ON.
Turn OFF from ON position:
Tap bottom of rocker – Lights turn OFF.
If there is a power outage, when the power is restored, the lights will return
to the last setting before the power interruption.
Cleaning:
Clean with a damp cloth.
DO NOT
use chemical cleaners.
OPERATION
TROUBLESHOOTING
• Lights Flickering
- Lamp has a bad connection.
- Wires not secured firmly under terminal screws of switch and/or
remote.
• Light does not turn ON and Locator LED does not turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Neutral not wired to switch (white wire).
- Lamp Neutral connection is not wired.
• Remote does not operate lights
- Ensure that total wire length does not exceed 300 ft (90 m).
- Ensure wiring is correct.
Push Pad
Locator
Light
NOTE:
To pair your switch with your mobile device, download the
Leviton Decora® Digital Switch and Timer app from the Google
Play Store or your iTunes account. Contact Leviton’s Techline at
1-800-824-3005 or visit Leviton’s website at www.leviton.com for
additional information.
This device complies with Part 15 of the FCC Rules. Operation is subject
to following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for
a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment OFF and ON, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving Antenna.
• Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/tv technician for help.
FCC CAUTION
Any changes or modifications not expressly approved by Leviton
Manufacturing Co., Inc., could void the user's authority to operate the
equipment.
FCC COMPLIANCE STATEMENT
Download the Leviton Decora
®
Digital Switch & Timer App for your
device.
Android:
Tap the Google Play Store icon on your phone or go to
http://play.google.com on your computer and follow the
instructions to obtain the app.
iPhone:
Tap the App Store icon on your phone or access the app
through your iTunes account on your computer.
Once you have downloaded the app, follow the instructions on the screen
to pair your mobile device with your switch. Once your mobile device is
paired, use the following options to control your switch:
•
On - Off:
Turns the switch ON and OFF.
•
Schedule:
Creates distinct ON/OFF events based on time and day.
•
Sleep Timer:
Sets countdown to turn switch OFF.
Advanced Settings
Device Options
•
Randomized Scheduled Events:
Cycles lights ON and OFF to
ensure a "lived-in" look while away.
• Hide Status LED:
Turns Status LED OFF.
• DST Offset Hours:
Adjusts the Sunrise/Sunset time in hours.
• DST Offset Minutes:
Adjusts the Sunrise/Sunset time in minutes.
CONTROLLING YOUR DIMMER WITH BLUETOOTH
®
This product is covered by U.S. Patent No. 8,664,886 and corresponding
foreign patents.
Copyright and Trademark Information
The Bluetooth
®
word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc., used under license by Leviton.
Use herein of third party trademarks, service marks, trade names, brand
names and/or product names are for informational purposes only, are/may
be the trademarks of their respective owners; such use is not meant to
imply affiliation, sponsorship, or endorsement.
No part of this document may be reproduced, transmitted or transcribed
without the express written permission of Leviton Manufacturing Co., Inc.
IC COMPLIANCE STATEMENT
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of
the device.
