TERMINATIONS
Termination Point
Wire Gauge
Strip Length
Torque
Main Breaker
300 MCM - #3 AWG
1.0 in.
250 in-lbs.
Main Lug
300 MCM - #3 AWG
1.0 in.
375 in-lbs.
Main Neutral
300 MCM - #3 AWG
1.5 in.
375 in-lbs.
Main Ground
2/0 AWG - #4 AWG
0.75 in.
50 in-lbs.
Load Power
(brass)
#4 AWG - #8 AWG
#10 AWG - #14 AWG
0.40 in.
0.40 in.
45 in-lbs.
35 in-lbs.
Load Neutral
(silver)
#4 AWG - #8 AWG
#10 AWG - #14 AWG
0.40 in.
0.40 in.
45 in-lbs.
35 in-lbs.
Ground Bus
#4 AWG - #6 AWG
#8 AWG
#10 AWG - #14 AWG
0.50 in.
0.50 in.
0.50 in.
35 in-lbs.
25 in-lbs.
20 in-lbs.
Step 4: Phase, Neutral and Ground Conductors
WARNING:
Use
ONLY
approved fittings and clamps to avoid
damage to wires.
a.
Bring the
phase (J)
,
neutral (K)
and
ground (L)
conductors
into the enclosure through the overhead conduit opening or a
bottom-feed knockout.
b.
Determine whether or not the application requires the use of a
main circuit breaker (M)
(fig. 5)
, or if
main lugs (N)
(fig. 6)
can
be used based on the local electrical codes.
c.
Connect the
phase (J)
,
neutral (K)
and
ground (L)
conductors
to appropriate terminals and torque to spec in the terminations
table
(fig. 5 or 6)
.
d.
If installing with a
main circuit breaker (M)
, also install the
two (x2)
terminal covers (O)
that have been provided
(fig. 7)
.
e.
When installing this enclosure as the service entrance, the
bonding strap (P)
MUST BE
installed
(fig. 8)
. Torque to 20
in-lbs.
f.
When installing this enclosure as a sub panel,
DO NOT
install
the
bonding strap (P)
.
NOTE:
For Service Equipment, apply “SERVICE DISCONNECT”
label (provided) to trim, near main breaker handle.
NOTE:
For Branch Equipment, apply “MAIN” label (provided)
to trim, near main breaker handle.
Step 5: Branch Circuit Breakers
WARNING:
Leviton
circuit breakers
MUST BE
used with a
Leviton
circuit breaker enclosure.
a.
Strip and connect the
load phase (Q)
and
load neutral (R)
wires to the
load terminals (S)
and ground wire to the
ground
bus (T)
of the circuit breaker enclosure
(fig. 9)
. Strip wires
and torque load terminals to spec in the terminations table.
NOTE:
Ensure that the main breaker is in the OFF position
before installing any branch circuit breakers.
NOTE:
Ensure that all branch circuit breakers are in the OFF
position before installing into the panel.
b.
Align the
hooks and guides (U)
of the branch circuit breaker
with the panel and press until breaker snaps into place
(fig. 10)
.
Step 6: Installing Deadfront
NOTE: Twist-outs (V)
must be removed for each position that contains
a branch circuit breaker. Fill any unused open spaces in cover using
filler plates
(see filler plate instructions)
.
a.
To remove
twist-outs (V)
, first strike with a screwdriver, then
twist with pliers until detached
(fig. 11)
.
b.
Install
deadfront (W)
by sliding it inward above the side wall
protrusions on each side at a 45-degree angle until bottom portion
of the
deadfront (W)
is seated into enclosure
(fig. 12)
.
c.
Secure the bottom of the
deadfront (W)
with the
securing
screw (X)
.
d.
Apply circuit directory labels on the back of the door.
Step 7: Complete the Installation
WARNING:
Before providing power to the load center,
check all electrical connections and confirm that the wiring
is correct.
WARNING:
Replace all doors and covers before
connecting power to this equipment.
a.
Ensure that the main and all branch circuit breakers are in the OFF
position. To energize, first turn ON the main breaker, and then turn
ON each individual branch circuit breaker.
SAVE THESE INSTRUCTIONS
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only)
1 800 405-5320 (Canada Only) www.leviton.com
PK-A3230-10-00-0A
© 2018 Leviton Mfg. Co., Inc.
Fig. 5
Fig. 6
Fig. 7
Fig.8
Fig. 9
Press until
breaker snaps
into place
Fig. 10
Fig. 11
Fig. 12
Align hooks
and guides (U)
Terminal covers
(O) (x2)
Ground
(L)
Phase wires
(J) (x2)
Main lugs (N) (x2)
Neutral
(K)
Main circuit breaker (M)
Ground
(L)
Phase
(J) (x2)
Neutral
(K)
Bonding strap
(P)
Ground
bus
(T)
Load terminals (S)
Load phase (Q)
Load Neutral (R)
Twist-outs
(V)
Securing screw (X)
Deadfront
(W)
45˚
WEB
VERSION
