background image

TO INSTALL:

NOTE:

 Leviton EDSR Switches may be mounted for Top or Bottom feed of supply wires 

(refer to 

Figures 2 and 3)

.

MOUNTING:
WARNING:

 TO AVOID FIRE, SHOCK, OR DEATH; 

TURN OFF POWER

 AT THE CIRCUIT 

BREAKER OR FUSE, AND TEST THAT THE POWER IS OFF BEFORE ATTEMPTING TO 

INSTALL ENCLOSURE.

CAUTION: 

THESE ENCLOSURES MUST ALWAYS BE MOUNTED VERTICALLY WITH 

RECEPTACLE END DOWN.

Note:

 Hinged cover will open only when the rotary switch knob is turned to the 

“OFF”

 position.

1.

 Remove the six (6) #10-32 x 1-1/4" cover mounting screws, and rotate the hinged cover open  

(refer to Figure 1)

.

2.

 Determine if the installation is “top” or “bottom” feed.

3.

 Drill appropriate hole size for conduit hub 

(not included)

 as indicated below in one of the four 

drill points indicated on the top and bottom of enclosure base. Drill points provided for top left, 

top right, bottom left and bottom right conduit entry 

(see Conduit Hub Mounting)

.

Enclosure Mounting Using Mounting Feet:
1.

 Orient mounting feet as desired 

(refer to Figures 2, 3)

 and secure to the enclosure base with 

the provided mounting screws #10-32 x 1-1/4". Torque to 10 - 12 in.-lbs (1.2 N-m).

Conduit Hub Mounting (Conduit Hub not included):
1.

 Route wires. Install 3/4" or 1" hub 

(not included)

 to conduit and enclosure. For 3/4" hub,  

drill a 1-1/16" mounting hole. For a 1" hub, drill a 1-5/16" mounting hole. Ensure that the  

"O" ring seats on the enclosure base outside wall. Install grounding bracket and secure  

tightly with hub nut.

 

2.

 Secure enclosure to the desired surface. Mounting hardware accept up to a 1/4" diameter 

screw 

(not included)

.

3.

 Make connections as per wiring instructions.

3

To “G” Term.

of Rcpt.

To “W” Term.

of Rcpt.

Neutral

Buss

Ground

Buss

Rotary

Switch

Auxiliary

Contact

Mounting Feet (4)

Listed Conduit Hub (not supplied)

Type 3R, 4X, 12K Rated

Ground

Bracket

Receptacle

(not supplied)

Condensation

Drip Loops

To “G” Term.

of Rcpt.

To “W” Term.

of Rcpt.

Neutral

Buss

Ground

Bracket

Listed Conduit Hub

(not supplied)

Type 3R, 4X, 12K Rated

Receptacle

(not supplied)

Mounting Feet (4)

Ground

Buss

Rotary

Switch

Auxiliary

Contact

Figure 2

Top Conduit 

Connection/Wire Entry

Figure 3

Bottom Conduit 

Connection/Wire Entry

CAUTION

THESE ENCLOSURES MUST ALWAYS 

BE MOUNTED VERTICALLY WITH 

RECEPTACLE END DOWN.

Summary of Contents for PowerSwitch EDSR














Reviews: