background image

4

Top or Bottom Feed:

 

NOTE:

 A metal closure plug must be grounded (bonded) back on to an unused ground  

 

terminal. Use of a UL Listed Watertight conduit fitting 

(not included)

 required to maintain Type    

4X and Type 12K ratings 

(refer to Figures 2, 3)

.

1.

  When using Top feed conduit entrance, always form condensation drip loops in wiring as  

 

shown in 

Figure 2

.

Wiring:

NOTE: 

Use conductors with insulation rated 75˚C or higher having sufficient ampacity in 

accordance with the 60˚C column of Table 310-16 of the NEC or Table 2 of the Canadian 

Electrical Code. 

DO NOT

 tin conductors.

1. 

WARNING:

 

TO AVOID FIRE, SHOCK, OR DEATH; 

TURN OFF POWER

 AT CIRCUIT 

BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!

2.

 From conduit, route Ground wire and Neutral wire to DIN mounted color coded Ground and 

Neutral terminals. Connect  Hot wire(s) to terminal(s) L1, L2, L3 on  DIN mounted Rotary 

Switch, as per wiring Diagrams 

shown on pages 8 to 9

 (loop wires as necessary). Route 

provided leads through receptacle mounting bracket 

and

 connect load side of switch T1, T2, 

T3  to appropriate receptacle terminals as per Wiring Diagrams. Connect Ground and Neutral 

Terminal (if applicable) of Receptacle to corresponding terminals on DIN mounted Terminal 

Blocks. Blue color terminal block is Neutral. Green/Yellow terminal block is ground. Tighten all 

screws to specified torques. Make sure that there are no loose strands.

  NOTE:

 The Conduit Hub steel bracket must be grounded (bonded) to the DIN rail mounted 

color coded Ground Terminal 

(refer to Figures 2, 3)

.

3.

   Strip Gages and Torques for LINE and LOAD terminals:

   

   For Neutral and Ground terminals, use #14-#8 AWG conductors, strip to 15/32" (12.0 mm)  

Torque 7.1 - 8.9 in-lbs (0.8-1 N-m).

   

   For Rotary Switch terminals, use #14-#8 AWG conductors, strip to 11/16" (17.5 mm)         

Torque 7 in-lbs (0.8 N-m).

   

   For Auxiliary terminals, use #18-#14 AWG conductors, strip to  5/16" (8.0 mm)                  

Torque 7.1 - 8.9 in-lbs (0.8-1 N-m).

   

  For Receptacle, refer to wiring instruction sheet supplied with device.

4.

   To wire the Locking Receptacle, feed the enclosed wires from Load side of switch, Ground 

terminal, and Neutral terminal up through the Receptacle Mounting Bracket  

(refer to Figures 2, 3)

.

5.

   Make sure there are no stray conductor strands.

6.

   Mount the Locking Receptacle to the Mounting Bracket. Use the two (2) mounting screws 

provided with the Receptacle.

7.

  Make sure there are no stray conductor strands.

8.

     Looping of wires as shown in 

Figure 2

 is mostly necessary for top feed installations to 

prevent possible condensation from dripping on to terminals.

9.

     Ensure that the enclosure cover’s gasket is in the groove. Close cover and tighten cover 

screws alternately to 10 in.-lbs. (1.2 N-m) of torque.

   

NOTE:

   For EDSR, switch knob must be in the “OFF” position to close cover.

10.

  Select Receptacle Voltage Label from label sheet provided. Affix Receptacle Voltage Label    

  to cover 

(refer to Figure 4)

.

11.

   When mating Receptacle with a 

WETGUARD

TM

 Plug, affix IP66 ratings label below 

Receptacle label as shown in 

Figure 4

.

     NOTE:

 When using a 20A Receptacle, the appropriate Gasket and Gasket Clamp 

must

 be 

used as per following installation instructions. If using a 30A Receptacle, your installation is 

complete.

Summary of Contents for PowerSwitch EDSR














Reviews: