Levitronix BPS-200 User Manual Download

Page: 5 / 36

User Manual for BPS-200

www.levitronix.com

PL-4012-00, Rev07, DCO# 20-144

System Name

Article #

Pump Head

Motor

Controller

Note

BPS-200.

100-901

LPP-200.1

(High Viscosity and
Density)

BSM-1.4

LPC-200.

Direct cabling between motor and controller.

BPS-200.

1 / 2

100-901

91 / 92

BSM-1.3

LPC-200.

1 / 2

Adaptor (0.5 - 10m) cables can be ordered according to Table 3.

BPS-200.

14 / 15

(ATEX)

100-905

56 / 57

BSM-1.6 (ATEX)

LPC-200.

1 / 2

Adaptor (0.5 - 10m) cables can be ordered according to Table 3. ATEX Cable Sealing
System can be ordered according to Error! Reference source not found.. ATEX and
IECEx certified.

BPS-200.

37 / 24

100-907

73 / 03

LPP-200.11

(Improved bubble and
priming behavior)

BSM-1.4

LPC-200.

1 / 2

Direct cabling between motor and controller.

BPS-200.

40 / 41

100-907

76 / 77

BSM-1.3

LPC-200.

1 / 2

Adaptor (0.5 - 10m) cables can be ordered according to Table 3.

BPS-200.

44 / 45

(ATEX)

100-907

80 / 81

BSM-1.6 (ATEX)

LPC-200.

1 / 2

Adaptor (0.5 - 10m) cables can be ordered according to Table 3. ATEX Cable Sealing
System can be ordered according to Table 4. ATEX and IECEx certified.

BPS-200.

50 / 51

(ATEX)

100-911

10 / 11

LPP-200.10 (Antistatic)

BSM-1.6 (ATEX)

LPC-200.

1 / 2

Table 1: Standard system configurations

Note 1: All systems are CE, IECEE (following CB scheme) and ETL (NRTL) certified.

Pos.

Component

Article Name

Article #

Characteristics

Value / Feature

1b
1c

Pump Head

LPP-200.1

(High Viscosity/Density)

LPP-200.11
LPP-200.10

(Antistatic)

(Improved priming/bubble
behavior)

100-90281

100-90702
100-90684

Impeller / Pump Housing
Sealing Ring
Fittings

LPP-200.1/11: High Purity PFA / PTFE

LPP-200.10: PFA / antistatic PTFE

Kalrez



perfluoroelastomer

LPP-

200.1/11: ½” Flaretek

LPP-200.10:

Pillar FM ½”

Max. Flow
Max. Diff.-Pressure
Max. Viscosity / Density
Max. Liquid Temp

21 liters/min / 55 gallons/min
2.6 bar / 37.7 psi
LPP-200.1/x: 50cP / 1.8 g/cm3

LPP-200.11/10: < 20 cP

C / 194

Pumphead Selection

LPP-200.1: Usage for higher viscosity and density
LPP-200.11: Usage for aqueious liquids and improved priming/bubble robustness

Motor

BSM-1.4

100-10005

Housing

ETFE (chemical resistant) coated Aluminum, waterproofed (IP67)

Cable / Connectors

1x 5m cables with FEP jacket / 1x D-SUB (direct cable to controller)

Motor

BSM-1.3

100-10004

Cable / Connectors

1x 2m cable with FEP jacket / 1x circular (M23, IP-67)
(needs extension adaptor cable for connection to controller)

Motor (ATEX / IECEx)

BSM-1.6

100-10063

Cable / Connectors

1x 2m cable with FEP jacket / 1x circular (M23, IP-67)
(needs extension adaptor cable for connection to controller)

ATEX / IECEx Marking

II 3G Ex nA IIC T5 Gc

II 3D Ex tc IIIC T100°C Dc

Standalone
Controller
(User Panel)

LPC-200.1

100-30008

(Controller with
PLC connector
incl. in 100-
90335)

Electrical Power / Voltage

200 W / 24 - 48V DC

Interfaces for
Standalone Controller

Panel to set speed (automatic storage on internal EEPROM)

PLC with

1x analog input (“Speed”)

4 - 20 mA

1x digital input (“Enable”)

0 - 24 V (optocoupler)

1x digital output (“Status”)

0 - 24 V (relais)

Standard Firmware

C2.25

Extended
Controller
(PLC and USB)

LPC-200.2

100-30009

(Controller with
PLC connector
incl. in
100-90336)

Interfaces for
Extended Controller

PLC with

- up to 4 digital inputs

0 - 24V (optocoupler)

- up to 4 digital outputs

0 - 24 V (relais)

- up to 2 analog inputs

4 - 20mA

- up to 2 analog inputs

– 10 V

- up to 2 analog outputs

– 5 V

USB interface (for service and system monitoring)

Standard Firmware

C2.48

Table 2: Specification of standard components

Note 1: Kalrez



is a registered trademark of DuPont Dow Elastomers

Note 2: Pump head

s with Pillar FM ½” fittings available.

Pos.

Component

Article Name

Article #

Characteristics

Value / Feature

Extension Adaptor
Cable for Power

MCA-1.4-05 (0.5m)
MCA-1.4-30 (3m)
MCA-1.4-50 (5m)
MCA-1.4-70 (7m)
MCA-1.4-100 (10m)

190-10228
190-10170
190-10187
190-10229
190-10230

Jacket Material
Connectors

PVC-jacket
Circular Hummel to D-SUB connector

Table 3: Specification of adaptor/extension cables

Pos.

Component

Article Name

Article #

Characteristics

Value / Feature

Air Cooling Module

ACM-1.1

190-10003

Material / Connection Port
Air Pressure / Consumption

PVDF / NPT ¼”
~ 0.5bar (7.2 psi)

Mounting Base Plate

MBP-1.1

190-10004

Material

PVDF

(a,b
,c,d

,e)

Impeller Exchange
Kits

IEK-200.1

(for LPP-200.1)

IEK-200.2

(for LPP-200.11)

IEK-200.8

(for LPP-200.10)

100-90517
100-90524
100-91109

Impeller (a) / Sealing O-Ring (b)
Pump Casing Screws (c)

Pump Motor Screws (d)

Exchange Tool IET-1.1 (e)

PFA    /    O-Ring, Kalrez, 50.52 x 1.78
IEK-200.1/2:   6 pcs M4 x 15 mm, PVDF
IEK-200.8:

6 pcs M4 x 16 mm, PTFE coated stainless steel

IEK-200.1/2: 4 pcs M3 x 16 mm, PVDF
IEK-200.8:

4 pcs M3 x 14 mm, stainless steel (SS)

POM-C

Ex Cable
Sealing System

ACS-A.1

100-90292

Sleeve (a) / Gasket (b)
Frame (c)
Cable Module (d)

Stainless Steel and EPDM
Roxylon (EPDM rubber)
Roxylon (EPDM rubber)

Note:
Lubricant (e) and measurement plates
(f) are included.

AC/DC Power Supply

TSP 360-124

(Standard Traco Supply)

100-40016

Voltage / Power Output /
Voltage Input
Dimensions

24 VDC / 360 W
85

– 132 / 187 – 264 VAC, autoselect

125 x 125 x 80 mm

Certification

UL, CSA, CB, Semi F47

AC/DC Power Supply

TSP 360-148

100-40017

Voltage / Power Output

48 VDC / 360 W (other specifications same as 9a)

Screw Set

Screw Set
SS+PTFE

100-90447

Number/Dimensions
Material

4 pcs M3x14 and 6 pcs M4x16
Stainless Steel+ PTFE coating

Needed to increase maximum static
pressure of pump head.

Table 4: Specification of accessories

Summary of Contents for BPS-200





































Search results

Summary of Contents for BPS-200

Reviews:

Related manuals for BPS-200

Brands by name

Popular brands

Levitronix BPS-200, User Manual

Search results

Summary of Contents for BPS-200

Reviews:

Related manuals for BPS-200

Brands by name

Popular brands