Levitronix PuraLev 600MU User Manual Download

Page: 5 / 41

User Manual for PuraLev

600MU

www.levitronix.com

PL-4033-00, Rev09, DCO# 20-144

System Name

Article #

Pump Head

Motor

Controller

Note

PuraLev

600MU.1

PuraLev

600MU.2

PuraLev

600MU.4

PuraLev

600MU.5

100-90590
100-90591
100-90593
100-90594

LPP-600.7 (PVDF)
(with drain port)

LPM-600.5
LPM-600.5
LPM-600.4
LPM-600.4

LPC-600.1-02
LPC-600.2-02
LPC-600.1-02
LPC-600.2-02

Adaptor/Extension cables according to Table 3

have to be

ordered as separate article.

ATEX Cable Sealing System can be ordered according to
Table 4.

Certifications: CE, IECEE CB scheme, ETL (NRTL), ATEX
and IECEx.

PuraLev

600MU.7

PuraLev

600MU.8

PuraLev

600MU.10

PuraLev

600MU.11

100-90596
100-90597
100-90599
100-90632

LPP-600.18
(PVDF)
(without drain port)

LPM-600.5
LPM-600.5
LPM-600.4
LPM-600.4

LPC-600.1-02
LPC-600.2-02
LPC-600.1-02
LPC-600.2-02

PuraLev

600MU.14

PuraLev

600MU.15

PuraLev

600MU.17

PuraLev

600MU.18

100-91325
100-91326
100-91328
100-91329

LPP-600.27 (SS)
(without drain port)

LPM-600.13
LPM-600.13
LPM-600.12
LPM-600.12

LPC-600.1-06
LPC-600.2-06
LPC-600.1-06
LPC-600.2-06

Table 1: Standard system configurations with motor controller and pump head

Pos.

Component

Article Name

Article #

Characteristics

Value / Feature

Multi-Use Pump Heads

(PVDF)

LPP-600.7

(with drain port)

LPP-600.18

(without drain port)

100-90287

100-90548

Impeller / Pump Housing
Housing Sealing
In-/Outlet Fittings
Max. Flow / Max. Diff.-Pressure
Max. Viscosity / Max. Liquid Temp.
Wet Pump Volume/Surface
Sterilization Methods

PFA / PVDF (FDA, USP Class VI, BSE/TSE/Animal free)
Triclamp EPDM (FDA, USP Class VI, BSE/TSE/Animal free)

Triclamp 1“ in/outlet, Triclamp ½“ for drain port (Standard: BS-4825-3)
75 liters/min (20 gallons/min) / 3.2 bar (46 psi)
50 cP / 90

C (194

113 ml / 363 cm

(without drain port)

SIP (Steam in Place), CIP (Clean in Place), Autoclaving

Multi-Use Pump Heads

(Stainless Steel)

LPP-600.27

(without drain port)

100-91319

Impeller / Pump Housing
Housing Sealing
In-/Outlet Fittings
Max. Flow / Max. Diff.-Pressure
Max. Viscosity / Max. Liquid Temp.
Wet Pump Volume/Surface
Sterilization Methods

Stainless Steel (EN 1.4435 / AISI 316L)
O-ring (DIN/SO 11864) EPDM (FDA, USP Class VI, BSE/TSE/ADI)

Triclamp 1“ for in/outlet (Standard: ASME)
75 liters/min (20 gallons/min) / 3.0 bar (43.5 psi)

30 cP / 90

C (194

115 ml / 374 cm

SIP (Steam in Place), CIP (Clean in Place)

2a
2b

Motor (ATEX / IECEx)

LPM-600.5
LPM-600.13

100-10039
100-10150

Housing
Cable / Connectors

Epoxy (anti-corrosive) coated Aluminum, waterproofed (IP67)
2x 3m cables with PVC jacket / 2x circular (M23, IP-67)

ATEX / IECEx Marking

II 3G Ex nA IIC T5 Gc,

II 3D Ex tc IIIC T100°C Dc

2c
2d

Motor (ATEX / IECEx)

LPM-600.4
LPM-600.12

100-10038
100-10149

Housing

ETFE (chemical resistant) coated Aluminum, waterproofed (IP67)

Cable / Connectors

2x 3m cables with FEP jacket / 2x circular (M23, IP-67)

Standalone
Controller
(User Panel)

LPC-600.1-02
LPC-600.1-06

100-30033
100-30086

(Power cable and
PLC connector incl.)

Voltage / Power

48V DC / 600 W

Interfaces

Panel to set speed (automatic storage on internal EEPROM)

PLC with

1x analog input (“Speed”)

4 - 20 mA

1x digital input

(“Enable”)

0 - 24 V (optocoupler)

1x digital output (“Status”)

0 - 24 V (relais)

Standard Firmware

For LPC-600.1-02: D6.25

For LPC-600.1-06: D7.25

Extended
Controller
(PLC and USB)

LPC-600.2-02
LPC-600.2-06

100-30034
100-30087

(Power cable and
PLC connector incl.)

Interfaces

PLC with

- up to 4 digital inputs

0 - 24V (optocoupler)

- up to 4 digital outputs

0 - 24 V (relais)

- up to 2 analog inputs

4 - 20mA

- up to 2 analog inputs

– 10 V

- up to 2 analog outputs

– 5 V

USB interface (for service and system monitoring)

Standard Firmware

For LPC-600.2-02: D6.48

For LPC-600.2-06: D7.48

Table 2: Specification of standard components

Note 1: See Section 6.7.

Pos.

Component

Article Name

Article #

Characteristics

Value / Feature

Extension Adaptor
Cable for Sensors

MCAS-600.2-05 (0.5m)
MCAS-600.2-30 (3m)
MCAS-600.2-50 (5m)
MCAS-600.2-70 (7m)
MCAS-600.2-100 (10m)

190-10226
190-10238
190-10127
190-10105
190-10239

Jacket Material
Connectors

PVC
Circular Wallmountable, Metallic (IP-67) to D-SUB

Extension Adaptor
Cable for Power

MCAP-600.2-05 (0.5m)
MCAP-600.2-30 (3m)
MCAP-600.2-50 (5m)
MCAP-600.2-70 (7m)
MCAP-600.2-100 (10m)

190-10227
190-10240
190-10126
190-10106
190-10241

Jacket Material
Connectors

PVC
Circular Wallmountable, Metallic (IP-67) to COMBICON

Table 3: Specification of adaptor/extension cables

Pos.

Component

Article Name

Article #

Characteristics

Value / Feature

Air Cooling Module

ACM-600.2

190-10140

Material / Connection Port
Air Pressure

PP (+ 40% Talkum) / NPT 1/4”
~1 - 3 bar (14

– 43 psi)

Air Cooling Module

ACM-600.3 (ATEX)

190-10410

Material / Connection Port
Air Pressure

PP EL-S (black,

conductive additive for ATEX applications) / NPT 1/4”

~1 - 3 bar (14

– 43 psi)

Fan Cooling Module

FCM-600.1

190-10401

Housing / Cable Spec.
Supply Spec. / IP Rating

PP (+ 20% Talkum) white / PP jacket, 3m, circular sealed M12
connector (PP).
24 VDC, 3.4 W / IP-65 (fan is IP68 rated).

Fan Cool. Module Cable

FCC-1.1-50 (5 m)
FCC-1.1-100 (10 m)

190-10407
190-10408

Specification

PP cable jacket with circular M12 connector (PP) to open wires

(A-F)

ATEX Cable
Sealing System

ACS-A.1
(Roxtec)

100-90292

Sleeve (A) and Gasket (B)
Frame (C)
2x Cable Module (D)

Stainless Steel and EPDM
Roxylon (EPDM rubber)
Roxylon (EPDM rubber)

Note:
Lubricant (E) and measurement
plates (F) are included.

AC/DC Power Supply

TSP 600-148-M

(M = Modified Levitronix design
from Traco)

100-40013

(Traco ID Number:
T1068-01A)

Voltage / Power Output
Voltage Input
Certification or Standards

48 VDC / 600 W
85

– 265 VAC (automatic detection)

CB, UL, CSA, Semi F47

Autoclaving Reinforcing
Tool

ART-600.1

190-10281

Purpose
Material / Mount. Screws

For stabilization of housing of PVDF pump heads during autoclaving
Anodized Aluminum / 4 pcs M6 x 25mm (Stainless steel)

Table 4: Specification of accessories

Summary of Contents for PuraLev 600MU










































Search results

Summary of Contents for PuraLev 600MU

Reviews:

Related manuals for PuraLev 600MU

Brands by name

Popular brands

Levitronix PuraLev 600MU, User Manual

Search results

Summary of Contents for PuraLev 600MU

Reviews:

Related manuals for PuraLev 600MU

Brands by name

Popular brands