23
CBT1:
CMOS Battery in 1x2 pin (1.25mm) wafer
CU1:
USB 3.0 type A connector
CU2:
USB 3.0 type A connector
CU6:
USB 2.0 port 1x4 pin (1.25mm) wafer
CU7:
USB 2.0 port 1x4 pin (1.25mm) wafer
CU8:
USB 2.0 port 1x4 pin (1.25mm) wafer
CL1:
RJ45 LAN connector
CL2:
RJ45 LAN connector
CL3:
RJ45 LAN connector
CL11:
LAN port 2x4 pin (2.0mm) wafer (option)
CL21:
LAN port 2x4 pin (2.0mm) wafer (option)
CL31:
LAN port 2x4 pin (2.0mm) wafer (option)
CC1:
COM1 2x5 pin (2.0mm) wafer
CC2:
COM2 2x5 pin (2.0mm) wafer
CFP1:
Front Panel connector 2x5 pin (2.0mm) wafer
CIO1:
4DI / 4DO 2x5 pin (2.0mm) wafer
CO1:
SMBus 1x4 pin (1.25mm) wafer
CPI1:
DC-IN 1x4 pin (2.0mm) Red wafer
EDP1:
eDP 2x10 pin (1.25mm) wafer
SIM1:
Nano SIM card socket
SODIM1:
DDR4 SODIMM H: 9.2mm
NGFF1:
M.2 B key 2242 H=8.5 sockets 75 pin
NGFF2:
M.2 B key 2242 / 3042 H=8.5 sockets 75 pin
HDMI1:
HDMI typeA connector
HDMI2:
HDMI typeA connector
DP1:
DisplayPort connector (option)
DP2:
DisplayPort connector (option)
Chapter-3
3-1 List of Connectors
Connection
This chapter provides all necessary information of the peripheral's connections,
switches and indicators. Always power off the board before you install the peripherals.
Summary of Contents for 2I640DW
