background image

NOTE: 

the  high-frequency  output  of 

this  sensor  is  <0.2mW-  that  is  just  one 

5000      of  the  transmission  power  of  a 

mobile  phone  or  the  output  of  a 

microwave oven.

Specifications

Summary

Installation sit: indoors, ceiling mounting
Detection angle: 360°
Detection range: 1-8m(radii.) (adjustable)
Time setting: 8sec to 12min (adjustable)
Light-control: 2~2000LUX (adjustable)
Working temperature: -15°C~+70°C
HF system: 5.8GHz CW Electric wave,ISM band
Power consumption: approx.0.5W

LX-MV-360S1 Microwave Sensor Instruction

Transmission power<0.2mW

The microwave sensor is according to the microwave doppler effect <the basic principle of radar> , it can be 

widely used in as automatic control switch, the security system, and automatic video control system of ATM, as 

well as other automatic induction control area. The detection way has the below advantages compared with 

other as follows: 1. Non-contact detection, 2. Suitable for bad environment, immune to temperature, humidity, 

noise, air, dust, light…3.RF interference ability, 4.Transmission power only 0.2 mW, It will not harm the human 

body. Simple insta easy wiring. We use appropriative micro processing integrator, not only for high 

sensitivity and wide range of detection, and on very reliable work, error rate is extremely low, It can stable 

working on the temperature range: - 15 ~ + 70 Celsius degrees.

th

Power source: 220-240V/AC 
                        100-130V/AC
Power frequency: 50/60Hz
Transmission power: <0.2mW
Rated load:
1200W/5A Max,tungsten(cosφ=1) (220-240V/AC)
300W/2.5A Max,fluorescent(cosφ=0.5) (220-240V/AC)
600W/5A Max,tungsten(cosφ=1) (100-130V/AC)
150W/2.5A Max,fluorescent(cosφ=0.5) (100-130V/AC)

96.00mm

42.00mm

Sensor Information

Sensing distance adjustment range

Sensing angle adjustment range

Height of installation2.5~3.5M

2.5-3.5m

360º

Max:8m

Max:8m

Min1m Min1m

www.lexing.com.cn

Summary of Contents for LX-MV-360S1

Page 1: ...ction way has the below advantages compared with other as follows 1 Non contact detection 2 Suitable for bad environment immune to temperature humidity noise air dust light 3 RF interference ability 4 Transmission power only 0 2 mW It will not harm the human body Simple installation easy wiring We use appropriative micro processing integrator not only for high sensitivity and wide range of detecti...

Page 2: ...ase against the Ceiling and mark drill holes see fig 3 paying attention to any existing wiring in the Ceiling 3 Drill the holes insert wall plugs 6mm dia see fig 4 4 Put the power wire and load wire through the base holes see fig 5 5 Screw the base into place see fig 6 6 Connect the mains power supply and the load wire to the connection terminal according to connection wire mark 7 Close the middle...

Page 3: ...also change NOTE after the light switches OFF it takes approx 1sec before it is able to start detecting movement again The light will only switch on in response to movement once this period has elapsed Light control setting The chosen light response threshold can be infinitely from approx 2 2000lux Turn it fully anti clockwise to select dusk to dawn operation at about 2 lux Turn it fully clockwise...

Page 4: ...nclosure The load work without any identifiable movement movement occurred but not identified by the sensor movement behind wall movement of a small object in immediate lamp vicinity etc Check zone setting The load will not work despite movement rapid movements are being suppressed to minimize malfunctioning the zone you have set is too small Check zone setting detection or Note please don t adjus...

Reviews: