Diagnostic Information
2-35
4045-XXX
Double Feeding Paper
Note:
If double feeding paper occurs mostly from the bottom of the
stack, check for missing or damaged restraint pads in the tray.
Multipurpose Tray
Paper fails to feed from the multipurpose tray.
The pick roll should make one complete revolution and stop with the
flat side down. If the pick roll turns but does not pick paper, check the
roll for signs of wear, oil or grease on the surface of the pick roll or
slick spots. If you find a problem, replace the pick roll assembly.
Check to ensure the media that is being fed through the
multipurpose tray assembly meets recommended paper
specifications.
Parallel Port Service Check
Run the
“Parallel Wrap Test” on page 3-10
.
Note:
The Parallel Wrap Test is designed to check the parallel port
hardware by using a wrap plug (P/N 1319128) and invoking the
Parallel Diagnostic Test. This test helps isolate the printer from the
parallel cable and host. The test provides failure information on the
display for approximately three seconds. If the test indicates that a
problem is detected, replace the controller board.
FRU
Action
1
Paper
Paper is usually the primary cause of
a double feeding paper problem.
Flex the paper before placing the
paper in the tray. Edge-welded paper
is the most common cause of double
feeding. Loading the paper in the
tray in different locations and
directions and using rough paper
and short grain paper also causes
double feeding.
Summary of Contents for Optra M410
